Jump to content
SAU Community

Recommended Posts

ok, well, 2 things - Do they come with some sort of warranty, and would you take $430 for them?

How long were they "tested" for?

Were they only bought to see if your current packs were stuffed?

Oh, and will these fit, meaning are you able to put the Engine Center cover back on? (So it looks stock) Thanks.

Sorry about all of the questions.

Edited by The Mafia
Link to comment
https://www.sau.com.au/forums/topic/155656-sold/#findComment-2897009
Share on other sites

ok, well, 2 things - Do they come with some sort of warranty, and would you take $430 for them?

How long were they "tested" for?

Were they only bought to see if your current packs were stuffed?

Oh, and will these fit, meaning are you able to put the Engine Center cover back on? (So it looks stock) Thanks.

Sorry about all of the questions.

Only warranty I can give you is that they work, if you buy them and I put them in your car they will work I can guarantee that . As with all elecronic parts you can stuff them up if you dont fit them correct, nobody will warranty that .

The price is $490 , no I wont take $430 , don't forget they are like new , if I didnt tell you they have been used you wouldn't know.

Very short period of time to rectify a fault on a car that turned out to be the CAS. ( not my car)

They are exacly the same as the stockers , so you can put the cover back on. Do you have a series II GTST? If yes they are suitable , If you have different car to your avatar then do a search to see if they are suitable using the part number in the pic. I know they are suitable for a series II GTST and R34 GTR.

Link to comment
https://www.sau.com.au/forums/topic/155656-sold/#findComment-2897464
Share on other sites

Only warranty I can give you is that they work, if you buy them and I put them in your car they will work I can guarantee that .

And I am pretty sure that's even more warranty than you'll get from Splitfire themselves, because when I got mine a couple of years ago the documentation specifically said that the warranty is only valid in Japan. Unless they've changed their warranty policy recently. $490 is a bargain, I would buy them in an instant if I was after some.

Link to comment
https://www.sau.com.au/forums/topic/155656-sold/#findComment-2902318
Share on other sites

And I am pretty sure that's even more warranty than you'll get from Splitfire themselves, because when I got mine a couple of years ago the documentation specifically said that the warranty is only valid in Japan. Unless they've changed their warranty policy recently. $490 is a bargain, I would buy them in an instant if I was after some.

Thanks for the comments jimX, i think they are well priced cionsidering they retail for $795.00 and they are almost new. If I can't get that I'll just keep them for spares for my car..

phatboi2010, They wont suit Rb20 mate, you will need DIS-001 for your car and GTRS up to series III R33.

These will suit RB25 from 95 on and RB26 R34 only.

Link to comment
https://www.sau.com.au/forums/topic/155656-sold/#findComment-2902417
Share on other sites

PM sent

P.M send , please get back to me ASAP , the latest by tonight to confirm that you want them. If I don't hear from you by tonight they will be offered to the next person that wants them ..

Link to comment
https://www.sau.com.au/forums/topic/155656-sold/#findComment-2902826
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...