Jump to content
SAU Community

Recommended Posts

im selling a used (barely) kkr430 with the dump pipe and v-band clamp. almost brand new condition with bugger all shaft play. driven less than approximately 2000km's.

i currently dont have any pictures, but can be viewed on otomoto's site. http://www.otomoto.com.au/kkrturbo.htm

for those of you who are lazy, here are the specs;

KKR430_lg.jpg

Compressor inlet pipe 69mm, compressor outlet pipe 50mm

48 trim compressor; inducer 53mm, exducer 76.5mm

Turbine wheel outlet 48mm, outer diameter 64.5mm

im looking for $650ono, now $500. $400 picked up this weekend only! -melbourne

i want this thing gone! going to buy a new setup next week people!

call Miguel on 0432315388 :happy:

some low quality pics attached

post-30568-1171793937.jpg

post-30568-1171793974.jpg

post-30568-1171794123.jpg

post-30568-1171794164.jpg

Link to comment
https://www.sau.com.au/forums/topic/156831-sold/
Share on other sites

it actually wasnt bolted on to my car, but a mate of mine made 205rwkw on dr.drift's dyno with standard afm and injectors, someone else on these forums made 210rwkw

Link to comment
https://www.sau.com.au/forums/topic/156831-sold/#findComment-2924341
Share on other sites

  • 2 weeks later...
will this be a direct bolt on to an r33 with all the lines suiting the KKR

wanting to know this too...

also whats the power rating of it aaannndd when does boost come on?

Oh and the 205kw your mate made, was that on a 32 or 33?

:D

Musky

Link to comment
https://www.sau.com.au/forums/topic/156831-sold/#findComment-2964368
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
×
×
  • Create New...