Jump to content
SAU Community

Recommended Posts

im selling a used (barely) kkr430 with the dump pipe and v-band clamp. almost brand new condition with bugger all shaft play. driven less than approximately 2000km's.

i currently dont have any pictures, but can be viewed on otomoto's site. http://www.otomoto.com.au/kkrturbo.htm

for those of you who are lazy, here are the specs;

KKR430_lg.jpg

Compressor inlet pipe 69mm, compressor outlet pipe 50mm

48 trim compressor; inducer 53mm, exducer 76.5mm

Turbine wheel outlet 48mm, outer diameter 64.5mm

im looking for $650ono, now $500. $400 picked up this weekend only! -melbourne

i want this thing gone! going to buy a new setup next week people!

call Miguel on 0432315388 :happy:

some low quality pics attached

post-30568-1171793937.jpg

post-30568-1171793974.jpg

post-30568-1171794123.jpg

post-30568-1171794164.jpg

Link to comment
https://www.sau.com.au/forums/topic/156831-sold/
Share on other sites

it actually wasnt bolted on to my car, but a mate of mine made 205rwkw on dr.drift's dyno with standard afm and injectors, someone else on these forums made 210rwkw

Link to comment
https://www.sau.com.au/forums/topic/156831-sold/#findComment-2924341
Share on other sites

  • 2 weeks later...
will this be a direct bolt on to an r33 with all the lines suiting the KKR

wanting to know this too...

also whats the power rating of it aaannndd when does boost come on?

Oh and the 205kw your mate made, was that on a 32 or 33?

:D

Musky

Link to comment
https://www.sau.com.au/forums/topic/156831-sold/#findComment-2964368
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...