Jump to content
SAU Community

Recommended Posts

Hey guys , recently i dynoed my car and after the dyno, i did a engine compression test and the numbers were pretty bad compared to 2 years ago ~ which was around 130 across all 5 cyclinders except for the 2nd cyclinder which is 100. But after adding some oil on the 2nd cyclinder, the compression on the 2nd cyclinder immediately jumped back up to 125 psi. So they concluded that the injector in the 2nd cyclinder is faulty. But after asking few other workshops, they are saying injectors and low compression rates are unrelated..

any ideas guys ?

Thanks

injectors are before the valves. The oil let the loose rings in cyl2 seal better which bumped up the compression, temporarily. If they added oil to the other cylinders they more then likely would have jumped up much the same, so across the board would have been something like 155.

Surely all the oil is doing is sealing the rings better which means that's what's no good in that cylinder. If the test with oil didn't go up then you would be looking at valves. That's my theory anyway.

Surely all the oil is doing is sealing the rings better which means that's what's no good in that cylinder. If the test with oil didn't go up then you would be looking at valves. That's my theory anyway.

thanks for the replies guys, so is it safe to say its unrelated and irregardless if the injector is faulty or not adding oil will bump the compression readings up ?

thanks for the replies guys, so is it safe to say its unrelated and irregardless if the injector is faulty or not adding oil will bump the compression readings up ?

Unrelated with injectors mate .

You are correct abo .

If a little amount of oil increases comp it means rings and or bore worn but don't forget a substantial amount will increase comp because the combustion chamber is smaller because of the oil . In a low comp cyl if puting oil in to it doesn't increase comp it means the valves are leaking.

Do a leakdown test as well.

leakdown test is the best test to do.

Remove the sparkplugs, remove the intake and oil cap do your test. if its intake valves and there is reasonable leakage you'll hear/feel it coming out the intake, same for exhaust if its piston/rings you'll hear/feel it coming out the oil cap. just make sure that each cylinder is firing TDC (top dead centre).

Its a good idea to turn the motor over a few times once spark plugs are removed just incase theres any foreign matter between the valve and the seat which will give a false reading.

leakdown test is the best test to do.

Remove the sparkplugs, remove the intake and oil cap do your test. if its intake valves and there is reasonable leakage you'll hear/feel it coming out the intake, same for exhaust if its piston/rings you'll hear/feel it coming out the oil cap. just make sure that each cylinder is firing TDC (top dead centre).

Its a good idea to turn the motor over a few times once spark plugs are removed just incase theres any foreign matter between the valve and the seat which will give a false reading.

Thanks guys for the replies, im sending my car in for the leakdown test tommorow. Will see how it goes and check out what is the problem

Cheers

Thanks guys for the replies, im sending my car in for the leakdown test tommorow. Will see how it goes and check out what is the problem

Cheers

HEy guys, got my leak down test and compression test done today. results were

Compression test Leak down test

cyc 1 : 155 10%

cyc 2: 155 20%

cyc3 : 155 5%

cyc4: 153 5%

cyc 5 : 150 5%

cyc 6 : 151 5%

looks like all went well and will be proceeding to the next mods :domokun:

Thanks for the feedbacks

HEy guys, got my leak down test and compression test done today. results were

Compression test Leak down test

cyc 1 : 155 10%

cyc 2: 155 20%

cyc3 : 155 5%

cyc4: 153 5%

cyc 5 : 150 5%

cyc 6 : 151 5%

looks like all went well and will be proceeding to the next mods :domokun:

Thanks for the feedbacks

That indicates bore and or ring wear on number 2. and to a lesser extend in number 1 as well .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep I will use a guide coat after putting filler, I will do it on the whole panel as I'm a beginner so chances I've made quite a few errors. In that photo, I think that was a low spot, I just for example said to pretend it's flat but I will put filler + guide coat after to assess where I'm at. Yep with that picture, the panel is wet as it rained when I took the photo. But all those scratches are completely smooth, I went over it with 240 grit and can't feel it, even with my nail digging into it. I was legit thinking to buy a 2k can and spray primer to see how it turns out but then thought to myself it's going to be a mess doing it haha. Good mention there. Thanks for all that info I think I know what to do next.
    • Prior to laying down the primer, you need to make sure the surface is completely level. For example, based on this picture, I strongly suspect that the areas marked in blue are higher then the area marked in green.  If you spray primer over this entire area, then paint and clear it, the finished result will 100% show the low area. It will stick out like dogs balls. Unfortunately the paint won't magically level out the low areas as you lay it down.  Without seeing it in person, I expect that the green area will need to be filled, then use a guide coat and check that the entire repair area is level with a large sanding block.  With this picture, are you saying that even though you can see the scratches, the panel is in fact completely smooth and flat? If this is the case sure you could prep and paint it as it is.     The picture with the paint you described as blistering, it's hard for me to comment on from the photo alone. It looks like the panel is wet? Dunno, looks strange. Does the panel feel as smooth as glass when you run your hand over it? **** Going back to your question again, generally you would only sand the primer if you made a mistake while laying down the primer.  If the panel is prepped properly and you lay the primer down properly, you should not need to sand the primer.  This wouldn't work - Don't prep the panel. Spray primer and see how it turns out. Sand the areas where the issues appear. Spray more primer and see how it turns out. Sand the areas....... Yeah you'd go round and round in circles getting no where. 
    • That's sick, thanks for that, mine has much the same mods on a 400R. I just don't have the heat exchanger yet.   Might be worth a trip down the M1 to Syndey for a tune.
    • Mate , this is the current mods list Current Mods list (Installed) RV37 Skyline 400R (SKYLINE) | FUJITSUBO  - Cat Back  RV37 Skyline 400R (SKYLINE) | FUJITSUBO  - Front Pipe AMS  - INFINITI Q50/Q60 RED ALPHA COLD AIR INTAKE KIT AMS  - Performance Heat Exchanger Intercooler AMS Alpha Performance Full Race Down Pipes ECUTEK tune form TuneHouse in Sydney .(Just over 2k) The car came with HKS - Power Editor but I had it removed for the full tune. I would say if you are using the car for street diving a proper tune would be better.    
    • Interested to see any videos of this or on the dyno. Mine currently has HKS secondary cats i am undecided if I want to remove them. What did it set you back to get the tube done? And what mods have you got to get that power? I was looking at a racebox flash tune but maybe a proper tune would be better if these guys are good.
×
×
  • Create New...