Jump to content
SAU Community

Recommended Posts

Hi,

I think I've already arrived at an answer for this one, but I thought I'd double check that I'm not being too harsh on this car :cheers: . In the market for a skyline, had an RACQ inspection on a 1993 GTS-T, 102'000 km (offered for $13'000). I guess I'm interested to see if the condition report is out of the ordinary or not for a skyline of this age, I'm inclined to believe it's no good (advice from friends) - I'll ring the inspector to verify my decision, and check if a compression test had been done while I'm at it. Just painful thinking ahead to how many such checks I may need to go through before I get a clean bill of health, as they're reasonably expensive :happy: . Anyway report was as follows (in summary car was rated to be in reasonable condition, with some items requiring attention). Main concern is seepage from differential.

Defects requiring attention

- Oil seepage differential centre, rear of gearbox

- No evidence of rear steer operating

- Plug missing spare tyre well (and spare tyre not present)

Other items noted

- Fluid seepage rear of clutch master cylinder

- Oil seepage lower engine

- Oil seepage air conditioning compressor

- Surface rust left sill panel seam

- Left door lock surround loose

- Scuff marks lower section from bumper bar

- Bottom of left rear guard damaged, surface rust on same

- Surface rust noted under boot areas, heavy rust left rear inner sill panel

- Sill panels / floor frames dented

- Pads worn, monitor

- Sections of exhaust system corroding, front shields, muffler in particular

- Outer tie rod ends dust boots leaking grease

- Front struts dust boots broken/loose

Any feedback would be appreciated!

On a side note, can anyone recommend a Jap performance workshop that carries out pre-sale inspections?

Thanks,

Jade.

Edited by lee81
Link to comment
https://www.sau.com.au/forums/topic/160489-buying-a-1993-skyline-gts-t/
Share on other sites

Sorry should have included that, it's an R33

Then thats easy, dont buy it :D

In all honesty it seems high price for a car that has some issues and it is the oldest of the r33's, i mean its the same age as my 32 ( I know which I'd have, haha :D ... you will never find a car that is perfect but its how many little issues you are prepared to accept. For that kind of money my mate got a mint R32 GTS-T but he did very well. I got my car a bit cheaper but its was stock as which i wanted and the paint was stone chipped etc cause the owner lived in the country, but i got a respray for $2k and got an exhaust, soon to get rims and suspension and with that I will have a car that I am very happy with. My main focus was a mechanically sound car.

To me it sounds like you need to see a few more and bring a friend, second opinions are always good. Best of luck

Edited by r32line

Thanks for the advice, that's 5/5 recommendations against (having asked friends).. damnit! :rofl:. So I'll have to look at some others, I might consider it if there's a significant drop in price, but otherwise I'll keep looking. Unforunately I'm keen on getting dark blue paintwork, and there's not nearly as many of those around as white/red/black models. I rang the inspector, he said while there is seepage he doesn't consider it a major issue to fix (causing long term drama), should just be a case of replacing the seals. Compression test had been done ('power balance' check as they list it), and results came out normal. His primary concern was rust, mostly surface rust, and one particular area around boot where it was getting a bit deep. I'm more concerned about engine condition, which he considers ok, seems it's more cosmetic issues with rust, suspects it has not been garaged (and that resale value will suffer if rust continues), as has more rust than a usual import.

Yeah like you said if it drops in price then you can consider it, but at $13,000 for a 93 model it would want to be better than it is.

The rust is a concern to me, on imports some of the cars in japan are driven in areas where it snows and they put salt on the road, this is bad news for the car as rust is a likely result. If it has already got rust arrears its not a good sign and a year later you could find it to be a lot worse.

So put all that to the seller and say at its current price it is not in your consideration, but you may consider it if its cheaper and u can spend money on it getting it all sweet.. Has it got any mods, or rims/kit/stereo? if not for $13k its quite pricey for what it is..... with the rust that is "getting a bit deep" and has your mechanic concerned then you really need to think if its worth considering at all. If so come up with a price that you would pay and be happy and then negotiate but do NOT go above that price.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...