Jump to content
SAU Community

R33 Instrumentation Cluster

NISMO_R33_GTS_T

By NISMO_R33_GTS_T,
in General Maintenance

 Share

Recommended Posts

NISMO_R33_GTS_T Apprentice

NISMO_R33_GTS_T

Posted
Posted

Hey guys,

After months of intermittent flickering/bouncing of my tacho needle....its seems as though my tacho has finally had enough and wont run past 2000rpm any more!

I've read the DIY guide by 'pushead' on removing the instrumentation cluster and it seems to be fairly easy.....btw awsome guide (lots of detail an great pics)...cheers.

I still have a few question though -

1) The guide finishes with the cluster coming out of the dash, but still connected.....what happens next? Are the wires running to the cluster - soldered? or do they use connnectors?

2) When replacing the cluster, do you need to calibrate it? How do u go about this calibration proceedure?

3) Does anyone know where i can buy a 'new' cluster? or can u only buy 2nd hand ones? How much am i expecting to pay?

4) Do you know of any instrumentation experts where i can get the work done? How much roughly am i looking at? (I dont know if i will do the work myself or not? It depends on how much stuffing around is involved and how cheap it is - to simply get the work done by someone else.)

Cheers,

:P

Link to comment
https://www.sau.com.au/forums/topic/163320-r33-instrumentation-cluster/
Share on other sites
ECR033 Mentor

ECR033

Posted
Posted
Hey guys,

After months of intermittent flickering/bouncing of my tacho needle....its seems as though my tacho has finally had enough and wont run past 2000rpm any more!

I've read the DIY guide by 'pushead' on removing the instrumentation cluster and it seems to be fairly easy.....btw awsome guide (lots of detail an great pics)...cheers.

I still have a few question though -

1) The guide finishes with the cluster coming out of the dash, but still connected.....what happens next? Are the wires running to the cluster - soldered? or do they use connnectors?

2) When replacing the cluster, do you need to calibrate it? How do u go about this calibration proceedure?

3) Does anyone know where i can buy a 'new' cluster? or can u only buy 2nd hand ones? How much am i expecting to pay?

4) Do you know of any instrumentation experts where i can get the work done? How much roughly am i looking at? (I dont know if i will do the work myself or not? It depends on how much stuffing around is involved and how cheap it is - to simply get the work done by someone else.)

Cheers,

:P

To answer your questions in order...

1) The wires to the cluster use connectors - just need to pop them out

2) I didn't calibrate my speedo when I installed my Nismo dash, but i did do some sanity checks - i.e checked the speed displayed on the speedo against the speed readout on my PFC and also got my g/f to drive next to my car and compared my speedo with the speed her car was displaying at 60, 80 and 100km/h. My speedo was pretty much spot on (give or take), so didn't bother calibrating, although I would've done so if it was substantially out.

3) I doubt that you'll be able to get a new dash cluster, although if they were available, then a Nissan dealer would be the best bet (they may be able to order in). If you're after a second hand dash, I have one in perfect working condition that came out of my S2 R33 that I'd sell for $150 (plus postage).

4) Replacing the dash is pretty easy - the DIY guide is excellent and you should be able to do it yourself without any problems, so you shouldn't need to pay anyone to do it for you.

Cheers :happy:

RBwhatever Veteran

RBwhatever

Posted
Posted

If you pull the cluster apart its possible to find whats wrong with it.

There could be a few 'dry' connections where the female connector is connected to the circuit board. you can tell this by looking at them and if the solder looks as if it has been broken.

This happened a to my pulsar when I had it. Just had re-solder those connections and bob's your aunty.

You might have a different problem though.

ps. why was this posted in the DIY section aswell?

NISMO_R33_GTS_T Apprentice

NISMO_R33_GTS_T

Posted
  • Author
Posted

cheers guys :huh:

i think ill take a look at it myself first...see if i can work out why its playing up, then go from there.

p.s. im not sure why this post appears in the DIY section as well - the first time i tried to post it, i accidently posted it in the DIY section and a message came up saying i couldnt post it in that section (the post was cancelled!) So i decided to post it here instead . Now its appearing in both??? I dunno? :happy:

NISMO_R33_GTS_T Apprentice

NISMO_R33_GTS_T

Posted
  • Author
Posted

It appears as though i have lost my copy of the DIY guide pushead posted about removing the instrumentation cluster!

Ive searched though the entire forum and cant seem to find a link that works (there is a DIY post with a link to pusheads guide - but the link doesnt work!) :)

Just wondering if anyone could re-post or re-link the guide....it would come in very handy, as i was planning on having a play with it tommorrow.

Cheers,

:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      Whoops!
×
×
  • Create New...