Jump to content
SAU Community

Recommended Posts

all prices in US dollor....

$500 for the exhuast sytem.

$1500 for the brakes

$300 for the tail lights

$1000 for the powerFC

all prices can be negotiated....

JASMA SR cat-back system..... this exhuast is very high flow for the note it puts out... its very quiet... sounds nice... Wont disturb the neighbors!

ebaay030af3.jpg

ebaay024fu0.jpg

ebaay029zb3.jpg

POWER FC for bnr34....... perfect condition

ebaay018yp8.jpg

ebaay020rf2.jpg

ebaay022yv8.jpg

stock brake lights... not a thing wrong with them... just replaced them with the nismo LED.....

ebaay002lv8.jpg

ebaay005kd1.jpg

stock R34 GTR Brembo brake system... calipers, rotors, pads..... 30,000 km/h

ebaay009zn8.jpg

ebaay006po6.jpg

ebaay008zf1.jpg

ebaay011kp7.jpg

ebaay014ve0.jpg

ebaay015xh0.jpg

ebaay017bh5.jpg

i can ship anywhere in the world... for a decent price....

Edited by kingleh

Where are you located?

How much for the brembos? (its the Forum rules or mods will delete your post..)

Why did you take them off?

Cheers,

Johno

Where are you located?

How much for the brembos? (its the Forum rules or mods will delete your post..)

Why did you take them off?

Cheers,

Johno

im located in the US

$1500 for the brakes....

i replaced them with a big brake kit....

ok i updated the thread with prices...

and tommarow i will update with shipping cost to aus from the states....

i have 7 PMs just about brakes... and had 5 within one hour of each other...

so far i was offerd $2000 for them...

but i already stated im asking $1500 US dollor.... so if anyone wants to get a bidding war going... you can... but the guy who asked 2k get them for 1500 so far......

do i have 1600?..... going once..... :(

Edited by kingleh

Its not nice to ask for more then what you originally aasked for :(

Where abouts in america are you? My father is currently there and I would be interested in the 4 Calapers only (not the rotors).

Depending on where you are located in america how much would you sell the 4 calapers for?

Edited by Blitz_R33

guys id be hunting COD on this one trader rating = 0 and also has a total of 4 posts .. he also is in america .. and selling high priced items..

Just a warning

i will only sell everyting.. rotors calpiers and pads..... at one time....

the south east....

can i have the state/city please? I assume you are ok with pickup payment?

What im offering is $1500 just for the calapers alone. You can then sell the rotors by themselves and get more $$. If you want to sell the whole thing, then fine, ill grab it all for $1500.

Edited by Blitz_R33
i will only sell everyting.. rotors calpiers and pads..... at one time....

the south east....

Well if you are on the level I have quite a few friends in the south east. PM me your number and i will get somebody to call you. If you are above board i will post it on here and they can bid their hearts out.

Dont be put out by peoples wariness. To most of us that is a lot of coin and you are inaccessible.

btw, what state are you in?

im over on GTR.co.uk if you guys wana search my posts... same screen name...

for serious buyers i will prove that im real through PM.... but i do understand how some could think i was a fake...

as of right now the brakes are pretty much sold.... so if that deal doenst go through.. then they will be back up for offers....

fineline... i will PM you if the current deal doesnt work out

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...