Jump to content
SAU Community

Clutch Options?

46n2
 Share

Recommended Posts

R33LIN Collaborator

R33LIN

Posted
Posted
wow....10,000kms? Ive got an exedy 6puck and its shudders like all hell anything under 2k, so it might get better further down the track? as ive only done 6,000kms odd so far...

But then again ive been told theyre sposed to do it? Because theyre meant for high rpm launches etc..

hey mate,

unfortunately ive heard that the driverability of puck clutches are more difficult and are subject to more shudder during take off. with those type of clutches...your either on or off. obviously if you dont get it right then it will shudder and so forth. i think the good thing about cushion button though is how its "cushioned" springs and hence it absorbs most of the shudder. i cant definitely say that after your clutch has bedded itself in it will be better. but yeah it should be abit better and less bitey.

goodluck mate,

:P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...