Jump to content
SAU Community

Painting Cooler Black + Piping... Any Special Methods?

DjeMz

By DjeMz,
in Engines & Forced Induction

 Share

Recommended Posts

abu Grand Master

abu

Posted
Posted (edited)
i don't think you would want your core powder coated - maybe the pipes, but that stuff is a bit thick. much thicker than spray paint or anodizing that's for sure. powder coat is tough for a reason.

i had mine painted by a radiator shop for $20 bucks. Looks fine to me although it's a little bit glossier than i was expecting.

I've seen intercooler cores powder-coated on twin turbo LS1 motors, running well over 240rwkw without an issue!

Some of them running 11sec passes at the track, and also being street driven, daily.

Dont think it would be an issue! It is quiet thick, but when exposed to air they to cool quiet well..

Edited by abu
abu Grand Master

abu

Posted
Posted
That doesn't sound like much power from a twin turbo LS1. Maybe it is a problem?

Anyway, I asked this question a while ago. http://www.skylinesaustralia.com/forums/in...c=54462&hl=

Hehe was a run in tune.

Car ended up doing a flat 11sec pass with a slipping clutch.

Will check out the link!

Thanks

abu Grand Master

abu

Posted
Posted (edited)

FORD XR6 turbo come out of factory with black powder coated FMIC.

There stock intercoolers are fairly small, but are good to flow between 270 -300rwkw, and has been proven by many!

APS also powder coat most of there intercooler black, along with many other workshops with big HP cars.

Edited by abu
kristafa Proficient

kristafa

Posted
Posted

re-worked my engine bay in the beemer..

i did my pipes in 2pak black.. been running like this for about 2 months now without any signs of the paint going bad.

cost me 60bucks for paint+hardener and still some left over :)

post-30449-1188309714_thumb.jpg

Craved Grand Master

Craved

Posted
Posted

powdercoating can be applied as thin or as thick (up to about 3mm) as you like.

the thinner the coating the rougher the finish it, but on a satin finished intercooler you could get away with a lighter coating.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Boost cut after swap(RB25DET NEO) R34

      By Kinkstaah · Posted

      I used to have Walbro 255's when they were a pretty common update. (or were they 044? 040?) In any case I had a dirty tank. I thought the tank was good, but I would find the filter would clog in maybe ~50km of driving. If the issue persists, well, your fuel system or tank has crap in it that the pump is sucking up.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Ok thanks for the info. I/we do not know what tune is on that Nistune ECU so it is why there is stock ECU and that Nistune is for later when the car is done. I have guy who tunes Nistune and other ECU so i will then take it to him to see and properly tune for the car   And for the update. On 99,9% it is bad fuel pump. Which is wierd cuz it is like 2 years old(brand new walbro 255) and that filter (also brand new) was dirty.  I was alwaya pumped premium(100) on very good petrol station so i dont know how is that possible...  
    • zillah
      Recommendation for engine oil funnel spill free

      By zillah · Posted

      Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Kinkstaah
      Boost cut after swap(RB25DET NEO) R34

      By Kinkstaah · Posted

      Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
×
×
  • Create New...