Jump to content
SAU Community

Recommended Posts

I know motec has the best hardware,thereby can do more thinks that power fc can(thats why is more expensive). I don't realy know if i need something like a motec since i don't aim at huge hp numbers.(i want 500-600 hp).Can the original ecu be remaped?Will it work ok in close loop?

What is "aux dig inputs","aux outpout","acel pump"?(because powerfc was none of the above.

Link to comment
https://www.sau.com.au/forums/topic/16649-aftermark-ecu/#findComment-342191
Share on other sites

for 5-600 hp you really dont need motec in fact the power fc is nearly as progammable as the motec if you use the software fc logit and it runs in closed loop it also comes with base map so you have the car running strainght away and it plugs in whenre the old ecu was in fact it looks very similar to the stock ecu the only realy draw back is that you need to run air flow meters but thats not so bad you can get larger ones from a z32 seriously at this level of tune the power fc is all you need regard less of cost. people make inexcess of 900 hp using the power fc with great driveability etc.

cheers

meggala

if you get one make sure you get a hand controller for it

Link to comment
https://www.sau.com.au/forums/topic/16649-aftermark-ecu/#findComment-342205
Share on other sites

no from what I knwo of the power fc it doesnt have different maps but the beauty of it is you cna retune the car after each up grade which help. If a car is well tuned it shoud be tuned for performance and economy the big factor with economy is to wind down the boost and to be on boost as little as possible

cheers

Link to comment
https://www.sau.com.au/forums/topic/16649-aftermark-ecu/#findComment-343002
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, plenty of air flow, there is a dedicated path that feeds the air in to the OEM intake tube behind the bumper As for a "tangible effect", maybe, but getting the pod/intake air out of the hot engine bay is worth it psychologically to me, even if it gives no performance difference, so the tangible effect in my Lizard brain saysss yessss  In the end, to me a tangible effect isn't always about performance, sometimes it a sound or a look, or even a...... feeling  Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga
    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
×
×
  • Create New...