Jump to content
SAU Community

Recommended Posts

Hi I have a R33 gtst. My car no matter if its hot or cold will not idle. This is what it does car starts easy, revs to 1900 rpm,drops to 1500, pause, then to 1000 for a sec then dies. Stalls all the time. Runs perfect above 1500 rpm.

I have a HKS Sq BOV.

I have tried so far:

Cleaning Acc valve and all that muck out of the back of the plenum

Repacing fuel filter

setting the TPS

Turning Idle screw in and out with the TPS disconected ( For some reson the IDle does not change 1 bit weather i turn it in or out)

Cleaning out the AFM

Located where the Ecu idle screw should be, to find the isnt 1 on it

checked for leaks

what have i missed? Can someone help me out please!

Link to comment
https://www.sau.com.au/forums/topic/166540-r33-idle-problem-need-some-help/
Share on other sites

1. Go back to your stock bov

2. Get a plumb back bov

3. Get a tune

your atmo bov will be releasing a lot of air into the atmosphere, yet your air flow comp will read it as being in the system, so the fuel will be added as if there is that amount of air in there... but its not... any of the 3 will fix this problem... normally an atmo bov wont cause it to completely die at idle, it does create idling and gear changing problems, but not normall this bad... which is why i said get a tune..

anyway, hope one of those fixes it for you :P

the bov i have i think is a plub bak though ( is that where a vacuum line sucks the valve open cuse its one of those) I dunno.

u know any tuning garages on the sunny coast?

thanks

a hks ssqv bov is atmo unless you have the recirc kit. is the plumback line blocked off?

Had the same problem...was running a HKS bov..and the car wont idle properly..only to find theres a slight vacuum leak from the HKS BOV as its a Atmo BOV..i put the stock BOV back and plumb it back into my intake pipe..problem gone..like wat DRD OFF said..the afm is gettin weird reading cos of the atmo BOV..

Had the same problem...was running a HKS bov..and the car wont idle properly..only to find theres a slight vacuum leak from the HKS BOV as its a Atmo BOV..i put the stock BOV back and plumb it back into my intake pipe..problem gone..like wat DRD OFF said..the afm is gettin weird reading cos of the atmo BOV..

man what the hell is drd off? :wave:

as for the original poster, you might want to save up some money and get a tune, you will notice that your car will run a shit load better... most well tuned skylines with atmo bovs wont actually stall, but if yours is, its a bit under the weather and could use a check up :wave:

i think you will like the change :unsure:

  • 2 years later...

please try an alternate stock ECU

my old ECU was fried and i drove a car like this for 6 months lol - not fun looking like a tool revving your car at every set of lights.

swap it out and see if you know someone with an stock ECU'd r33

hi guys

May not be the problem but i found info in regards to small cracks/holes in the little vacuum line on the turbo

Also my car played up bad one day turned out the boost/vacuum line to my gauge was leaking a little causing same problems as listed above

I would go round the engine bay with a can of carby clean or start ya basterd and see if there is any leaks else were i know you said you checked for leaks but it dose'nt take much to create a problem

happy leak hunting

Hi I have a R33 gtst. My car no matter if its hot or cold will not idle. This is what it does car starts easy, revs to 1900 rpm,drops to 1500, pause, then to 1000 for a sec then dies. Stalls all the time. Runs perfect above 1500 rpm.

I have a HKS Sq BOV.

I have tried so far:

Cleaning Acc valve and all that muck out of the back of the plenum

Repacing fuel filter

setting the TPS

Turning Idle screw in and out with the TPS disconected ( For some reson the IDle does not change 1 bit weather i turn it in or out)

Cleaning out the AFM

Located where the Ecu idle screw should be, to find the isnt 1 on it

checked for leaks

what have i missed? Can someone help me out please!

Make sure your fuel pump dropping resistor is plugged in. If any work has been done on the aerial recently it is possible the resistor plug has been unplugged. It is located in the passenger side rear cavity behind the wheel arch (where the jack is located). It is a rectangular silver item with a 2 pin plug.

Cheers

Ben

You sorta can and you sorta can't. Do some research on Nistune.

Are you running an after market plumb back BOV? What else is installed?

i've also got a hdi GT spec hybrid intercooler, aftermarket coilpacks, a boost controller (only running 10 pound) and a HKS cat back exaughst system.. apart from that i'm stock.. i've checked for leaky hoses and i've tried a different ECU and i've replaced my air flow sensor..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...