Jump to content
SAU Community

Recommended Posts

I bought this motor off Ash (R31Nismoid) and had It Freshened up by Racepace Motorsport as

soon as I got it. Was originally built by Racepace as well

Motor has not been ran in and has 0kms on it since freshened up

Only reason it is 4 sale is I have a change of plans for cars

All parts used in this build were brand new.

Only 2nd hand part was the GTR Rods which were checked

Motor bits

Arias 87mm Forged Pistons

Prepped GTR Rods

Machined/honed/prepped bottom end (and all that goes with it)

Nismo Bearings

Modified Oil galleries

Brand new headgasket

N1 oil pump

N1 water pump

All new belts/pulleys/tensioners

Nismo 740cc injectors

Z32 AFM,

Also comes

Turbosmart 45mm Ext Gate running a 15psi spring combination

Gate comes with all fittings and a screamer pipe

Apexi PowerFC with Hand Controller

Also able to supply a RB25DET gearbox at extra cost

Motor made 369rwkw@24psi when Ash had it

All the motor needs is turbo and manifold and u have a very tough motor

capable of making over 350rwkw with right turbo.

Price:$7000 without gearbox

$8000 with RB25DET gearbox

Pm for more details or ph:0417374102

Edited by BLUEGTR
Link to comment
https://www.sau.com.au/forums/topic/166713-rb25det-forged-motor/
Share on other sites

What cams, stock?

or is it just bottom end + other bits

Where are you located?

Thanks

Its full motor just needs manifold and turbo to be complete

Still stock cams was no need to change.

Located in Tassie

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...