Jump to content
SAU Community

Recommended Posts

I have an R33 GTS-T 4door ('94), and just recently when I start my car there is a noise coming from the dash or somewhere in that general area that sounds like a pulsing beat. It sounds as if something is trying to move or open and is getting stuck or held back by something. Kind of like the sound a pedestal fan makes when you try and stop it from oscillating. My friend, who dyno tunes ands works on alot of Skylines says its a common problem with them but he is not sure what it is.

Please help. If anyone knows what it is and how to fix it please let me know.

:thumbsup:

when i reset my ecu (disconnect the battery) and then re connect. after a drive or when i start it up, it makes a ticking king of noise. sounds like someones on a typewriter.. i assume its just the ecu , but i dunno if your in the same boat. it goes away after 2 or 3 drives . i.e happens less and less

when i reset my ecu (disconnect the battery) and then re connect. after a drive or when i start it up, it makes a ticking king of noise. sounds like someones on a typewriter.. i assume its just the ecu , but i dunno if your in the same boat. it goes away after 2 or 3 drives . i.e happens less and less

Nah this noise happens almost everytime i start the car and only lasts for 10-20 seconds then stops. I've been told that it may be a problem with the aircon unit. See link below:

http://www.skylinesaustralia.com/forums/in...howtopic=168054

I know what you mean. It sounds like a windscreen wiper motor going back and forth twice. Very faint though can hardly hear it.

thought it was just my car hehehe

I wouldn't mind knowing what that sound is too, it comes from inside the dash

One of the motors for the air vents perhaps... could be catching on something or broken. Just try'n pin point where exactly the noise is coming from, if it's behind the plastics dash facia thing pull it apart and have a look. There's DIY how to pull dash apart if needed, it's fairly easy to do though.

Its something to do with the fans from memory.

There is a post on here somewhere as well as a how to fix it tutorial. Not really worth fixing though. Its a whole dash out job.

It causes no damage anyway.

that my friends is the motor that directs the air flow for the aircon/heater system. its a little servo and over time the gears wear down and they start to slip. when i bought my r33 it was making the same noise and the dealer i bought it off fixed it before i picked it up. massive job, whole dash and aircon system needs to come out as its right down near the firewall on the inside of the car. good luck with that one...

  • 2 weeks later...

its the charming noise of 33 owners, very common, something to do with climate control unit, which i ve heard people have replaced and they go again in 6 months or so.. try moving the direction of air on different settings every time you start it and see where is happy meduim is.. i use to vent my on fresh air both face and leg postion and it didnt make a sound, though on other postions knocked persistenlty..you got to love it hey

I find there are two noises. There is the noise that is the climate control. The best way to reduce this noise I found was to turn the fan speed up to full for a bit then turn it back down again and the noise seems to be a lot less noticable.

The other pulsing noise that I think JodieR33Chick is refering to actually comes from behind the dash. My car made that noise for a few weeks after I got my car. Then it mysteriously went away and only comes back very occaisionally. I thought it may have to do with the dramatic change in climate from Japan to Australia (I'm first Aussie owner) and that it was something behind the dash expanding in the heat. It may sound stupid but I don't know how else to explain the pulsing noise as it seems to be so inconsistent.

i also sometimes come across that problem...it definately has something to do with the aircon unit....it sounds like the motor is sliping or someting weird is going on....best thing to do is to play around with the settings and it just might go away....i have my airflow at the leg and sometimes when i do switch it to face it makes the ticking noise but only when i turn the car off and on again....so best in my situation was have it pointing to the leg....u most likely have to play aroung and hopefully it goes away for you....best of luck

yeh mine only happens when i start the car up, even if i dont have the aircon or anything on, just thumps for about 4 seconds and thats it, never happens again until i start the car again\strange.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...