Jump to content
SAU Community

Recommended Posts

my passenger side window has stopped working but the drivers side is working perfectly fine.

anyone have any ideas to why this might be happening?

It could be a number of things so its a matter of trial and error really.

Start by taking the switch out making sure it hasn't come loose/off and go from there.

Do you have control from the drivers side to it?

Link to comment
https://www.sau.com.au/forums/topic/169383-power-windows/#findComment-3131002
Share on other sites

probly the passanger windows motor has burnt out, its pritty common and you can get a brand new motors from alljaps wreckers for $125.

good luck

Aif.

if the switch to that window has lost its SprIng tension it will cause the window to stay on down and burn the motor out. if it feels softer then the others switchs then you'll need to replace it aswell or you'll need another motor.

Link to comment
https://www.sau.com.au/forums/topic/169383-power-windows/#findComment-3132681
Share on other sites

yes i can put the window up/down via a button on the drivers side.

why does the motor burnt out though>?

So i would start with the switch in the passengers door to see if the plug has come off/loose or faulty. Also check the wiring to make sure thats all ok :)

Link to comment
https://www.sau.com.au/forums/topic/169383-power-windows/#findComment-3134872
Share on other sites

hey all

the window is now fixed!!!!!!!!!!!!!. there is a little button on drivers side that "locks" the passenger window!!!

i didnt know this!!!! thanks to Tint a car @ murray bridge for helping me!!!!!!!!

and thanks to everyone here too!!

Link to comment
https://www.sau.com.au/forums/topic/169383-power-windows/#findComment-3142323
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...