Jump to content
SAU Community

Recommended Posts

Wot up bought a house and sheds to small need to get rid of a heap of my stuff here goes

2 Work Rims 18 by 9inch wide +20 offset 4 and 5 by 114.3 no centre caps bit of gutter rash

70% falken 235 45 tyres SOLD

4 momo rims 6 spoke 17 by 7.5 +35 offset 5 by 114.3 sold my van so dont need them any more

come with all centre caps $550 open to offers

6 r33 gtst s1 coilpacks all work fine no cracks etc SOLD

hicas motor from r33 gtst s1 $30

R33 castor rods stock excellent bushes SOLD

R33 gtst aircon condenser compressor and under bonnet pipework all excellent condition

all removed by me who is a fridge mechanic (not dodge) may even regass in sa $250

r33 s1 rear seat couple of tiny marks $80

rb25 stock exhaust manifold $50

2 standard r33 red mirrors work perfect $100

Right and left rear trims the ones with arm rests and the ones the rear seatbelt goes through

r33 s1 $30 each

r33 roof lining for sunroof model few marks $40

2 crossfire 15 inch subs 1000wrms amp and 2 1 farad capacitors $800

left and right r33 rear rotors plenty left $50

r33 handbrake shoes heaps of meat $50

r33 s1 airflow meter and plug $120

r33 s1 ecu $100

r33 s1 rear bar red $80

space saver wheel $40

r33 stock intercooler SOLD

rb25 stock injectors by 6 $80

left and right r33 gtst stock guards good condition red

with gt badges $150

pm if you want more pics

willng to post if the $ right

open to offers on most items please no time wasters

Cheers Andrew

post-31558-1180924808_thumb.jpg

post-31558-1180924825_thumb.jpg

post-31558-1180924854_thumb.jpg

post-31558-1180924888_thumb.jpg

post-31558-1180924906_thumb.jpg

post-31558-1180924942_thumb.jpg

post-31558-1180924960_thumb.jpg

post-31558-1180936514_thumb.jpg

post-31558-1180936534_thumb.jpg

post-31558-1180936553_thumb.jpg

post-31558-1180936573_thumb.jpg

post-31558-1180936594_thumb.jpg

post-31558-1180936622_thumb.jpg

post-31558-1180936643_thumb.jpg

post-31558-1180955398_thumb.jpg

post-31558-1180955425_thumb.jpg

post-31558-1180955446_thumb.jpg

post-31558-1180955476_thumb.jpg

post-31558-1181446226_thumb.jpg

post-31558-1181446243_thumb.jpg

Edited by holes
Link to comment
https://www.sau.com.au/forums/topic/171321-cleaning-out-my-shed-adelaide/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...