Jump to content
SAU Community

Recommended Posts

My R33 struggles to start from cold. In the morning I'll start it and will need to really pump the accelerator before it will take. Every other start after that will be fine, but the next morning it struggles again. I always leave it on ignition only for a few seconds for the whole thing to get ready before I actually start.

From reading just about half the posts on SAU I have found that this is a fairly common problem and there are many possible causes :worship:

I think I have narrowed it down though and need some other opinions

I have a volt meter in my car and when starting it will drop to about 8 volts... from what I understand... this is way too low

If I understand correctly, this is caused by the starter motor arcing due to worn brushes

I was thinking of getting a starter motor from a wreck and swapping them over to test the result

Does this seem like the logical next step? Does anyone have any other opinions on the problem?

My car is a '93 R33 Series I GTS

In summer when the temperature is higher, the car starts fine, but the voltage still goes to around 8 volts.

Thanks... really want this sorted :)

Link to comment
https://www.sau.com.au/forums/topic/172314-engine-struggles-to-start-when-cold/
Share on other sites

Check your sparkplugs, running high-octaine fuel? got your car serviced recently?

8 volts is a bit low, on standard I think my car stays on like 12 volts or something. Also, have you checked your battery - enough charge in there - here's an inexpensive thing you could try - bring it to a mechanic, as him to fully charge up your battery for you - would cost around $20.00 or something, then see how you go. I've noticed with my car if I don't drive it enough, sometimes it will die down a bit.

Good luck.

My battery is brand new... found the most powerful one that would fit in the space

I tried putting in new spark plugs, but no change and I always use BP Ultimate 98RON

Didn't know about the oil though... I replaced the oil a few months back, can't remember the viscosity, but it was recomended to me by the mechanic for my car and its k's, so should be ok

Any other ideas? When I start it after its already been started once in the day, the voltage doesn't drop as far. It drops to about 10 volts. Its only the first start on a cold morning that it drops really low and struggles.

Thanks for the input so far guys :thumbsup:

I'm not too sure mate, I think it depends on how worn out your engine I think. The more worn/old it is, the thicker the oil should be. I don't know much about oils honestly.

Hopefully someone who does know will come and give their recommendations.

well boys i have had this same issue over the past 6 months, and it's a common thing, but belive me there is no sollution that i found.

I had replaced everything in the car, electrical that is, all new sensors, and test and so forht, you name it we tried it, eaven a new set of injectors, no good, then one day it came good, no idea how or why, but has been fine everysince. So bugga.

It's a pain in the ass to find too, seing as you only get one chance a day to diagnose it.

Personaly, i would start by cleaning your AFM. Also test or buy a new Engine temperature sensor, as this oftern plays havoc with the car. also put a new fuel fulter in the car and get the injecotrs cleaned, it may be that one is leaking a bit.

After that it's all trial and error.

I had new AAC valve, CAS, AFM, TP, ECu temp sensor, ECU, COILS, ect ect.

Thanks WogsRus... In my many hours of searching the forum I read heaps of things you had written... I will be trying all these things and hopefully don't struggle as much as you did :)

It may take a while to test each thing, because, as you said, you can only test what you tried once a day... I'll keep this post updated each weekend I try and make progress for all the others with the same problem... hopefully we get it sorted out ;)

If anyone else has any more insight, please let me know

Cheers

hey adam

i have the same car and the same problem..with mine it clicks over first time but the rev's are very low like its going to die but after a second the rev;s jump up the correct idle...

interested to find out

Any chance you've got a fmic installed? I noticed that I had to blimp my throttle everytime I start the car in the mornings for it to get going after I installed my fmic. Not sure why it happened after the installation of the cooler, but I've had to. A little blimp of the throttle to get the car going isn't a big deal.

when you crank a car it's getting pretty close to a short circuit across the battery (you pull a LOT of amps) so the voltage will definitely drop - 10V would be a GOOD figure. 8V is probably normal.

maybe the cold start sensor is buggered or something? I assume there's a coolant temp sensor that's different to the one that runs your gauge....

i had the same probly on my r32 i cleaned acc valve ect but havent cleaned the one under the plenium yet... but ive found it struggles on cold mornings like you but lately ive been putting the siliencer in my exhaust in the morning when i start it and let it warm up bcoz my cars very loud.... and its always starts first time no worries with the siliencer in its quite funny... :D good luck who knows what the real problem is behind it but everyones car seems to do it.

I started my car the other day (r33) and as Idont drive it often it struggles in cold also.

It actually seemed like my coils as it sounded a bit like a rexy, did that for about 3 seconds and then ever again.

Must admit also there was a different smell coming out of the exhaust - bit like a kero smell rather than fuel!

weird.

I try and start it now once a day

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Block bump. $400. As above cyl 6 needs bore or sleeve.
    • I would think making the argument that the travel is limited by a spring flexing against a spring perch as "the same method". Later on in the document they do state that the spring can't bind on full bump travel and cannot come loose in full rebound travel as well. (which is all very sensible). The laws are actually pretty sensible and reasonable. It's just that the people who enforce and check them don't actually read them or know them accurately. "Oh, coilovers? Instant fail mate. Don't even need to look at it." - Guy who will be instantly reported by me. There is probably merit to people who do get defected for height also get defected for the suspension in that state that allows it. I did never consider the people who are complaining about coilovers being picked on are also running around at 50mm off the floor.
    • I think given SAU's knowledge of E85 we can strongly conclude that 10% ethanol in almost any situation is entirely fine. Almost all of the myths against E85 were overblown, let alone E10.
    • From your link See bold text, is this referring to damper settings, if so that may a issue for "some" inspectors, I cannot see aftermarket coilovers having the evidence that "must be available that its functional performance is equivalent to the original" Maybe just remove the adjustment knows and hope for the best???? Meh 5.2 Suspension travel In all instances, modifications to a vehicle’s suspension must ensure the integrity of the system and not compromise the ride quality. At least two thirds of the original suspension travel should be maintained in both directions (rebound (i.e. extension) and bump (i.e. compression)), and rebound must be limited by the same method used by the vehicle manufacturer or if this is not practicable due to the nature of the modification, an equivalent method. If an alternative method is used, evidence must be available that its functional performance is equivalent to the original.
    • They actually don't - They adhere to VSB14 rules just like Victoria. The rules are against CABIN adjustable height, and it quite clearly states that the height has to be within parameters. I asked the VASS engineer to confirm this when I got my car engineered and they refused to engineer the coilovers because they didn't meet the requirements for requiring engineering. (mine are height adjustable.) People "Not wanting to bother" with "Actually reading/knowing/adhering to the rules" should result in fines and immediately losing the ability to issue blue slips and/or RWC's in Vic.
×
×
  • Create New...