Jump to content
SAU Community

Recommended Posts

sorry to start anotehr thread up but i couldn't find ne other thread...i need the stock horse power for the R33 GTS and GTST engines to complete my engine swap form >_< i know its like 184kw for the RB25det but i need a horsepower figure :P hehe preferably in HP

Cheers

Chi

sorry to start anotehr thread up but i couldn't find ne other thread...i need the stock horse power for the R33 GTS and GTST engines to complete my engine swap form >_< i know its like 184kw for the RB25det but i need a horsepower figure :P hehe preferably in HP

Cheers

Chi

eric mate for GTST power output is 184kw which is 247hp =)

hope that helps

and also found out power output for GTS is 190hp which is 141kw

hmmm so does my car have to go in for a vehical inspection since the turbo engine has a higher horse power out put then my NA one?

cause it states:

i decalre that all information contained in this application is true and correct and that the engine configuration has not changed

Note: if configuration of the engine has altered to the extent that the number of cylinders, RAC horsepower rating or fuel type altered then the vehicle must be presnted for examination and a CERTIFICATE OF INSPECTION COMPLETED.....

so guys ?!

Cheers

Chi

yeah it does need an inspection, its had an increase in horsepower, so you will likely need an engineers certificate to prove that your brakes are adequate (will probably need gts-t brakes, but you are getting them arent you?)

i put it down as 250hp *cough* when i changed it. :)

ahahah cheers mitch :) ur a top fellah :domokun: hmmm *cough* 250 hp *cough* *cough* mmm mitch i can't come down this week for the guage and btw is it mechanical or electrical if thats such thing? ill come down next week haha

Cheers

Chi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...