Jump to content
SAU Community

Recommended Posts

RAYS ENGINEERING WHEELS - MODEL - VOLK RACING TE37.

Full set of 4 - 18 x 9.5 inch wheels with YOKOHAMA 235 x 40 x 18 tyres Fronts (70%tread) and Michelin Pilot 265 x 35 x 18's Rears (30-40% tread)

RIMS are in very good condition, 2 have minor gutter scrapes.

Offset +12 is to suit R33 and R34 GTR's

Pick Up in Melbourne. Wheels are in Melbourne. Can be sent interstate at buyer's expense.

$2600.00 - first to see will buy..

Info on this wheel :

Material is 6061 aircraft grade aluminum. This material is hot forged. 1st forging process is done with pressure of 5,000 kilograms per square centimeter. 2nd forging process is a slow process with 3,500 kilograms per square centimeter. The lip is also forged to 3,500 kilograms per square centimeter. This allows the wheel to have less material than other wheels, but have more strength and durability. The excess material is machined off (to tolerance of 1/100 of a millimeter). Powder coating and clear coating is done by a special proprietary process to ensure long lasting quality and durability

post-26639-1181734045_thumb.jpg

post-26639-1181734088_thumb.jpg

Edited by kitch15
Mate do you know if these wheels will fit on a r32 gtr v spec>>

cheers :thumbsup:

Relatively sure they will fit any R32 GTR but will stick out... will look tough as hell but may have clearance issues at full lock etc... I could be wrong however.

Running 235/40/18 front and 265/35/18 rear on a gtr is fine. The rolling diameter is about the same for these 2 sizes and doesn't really affect ATTESA. I'm using these sizes of dunlop dz02g semislicks on the circuit and never had a problem with my gtr32.

Running 235/40/18 front and 265/35/18 rear on a gtr is fine. The rolling diameter is about the same for these 2 sizes and doesn't really affect ATTESA. I'm using these sizes of dunlop dz02g semislicks on the circuit and never had a problem with my gtr32.

Thats exactly right J-Boy. 265's on front would struggle in an R32, in terms of clearance. Hence the smaller tyre choice.

Have a genuine buyer looking at the wheels today, so most likely sold.....sorry guys.....if falls through, will let you know tomorrow, to other interested buyers...Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...