Jump to content
SAU Community

Sold

lrc135
 Share

Recommended Posts

lrc135 Enthusiast

lrc135

Posted
Posted (edited)

I bought these 3 weeks ago to assist eliminating tuning and defect issues. But the problems have been fixed without fitting these parts. And now I need funds to help pay the bill.

And the manifold was new when i bought it. It is a greddy replica. I'm trying to make this obvious because the guy tried to sell it to me as a genuine item. Anyway.. I have spent about 10 hours polishing the runners in the manifold because I wasn't happy with the casting finish. I never tried to port it bigger, I just took enough off to make the surfaces smooth.

Throttle body sold

Manifold dropped SOLD

Edited by lrc135
Link to comment
https://www.sau.com.au/forums/topic/172673-sold/
Share on other sites
75coupe Grand Master

75coupe

Posted
Posted
I bought these 3 weeks ago to assist eliminating tuning and defect issues. But the problems have been fixed without fitting these parts. And now I need funds to help pay the bill.

The thottle body is uses but in excelent condition. And does not reqire an adaptor for the manifold below.

And the manifold was new when i bought it. It is a greddy replica. I'm trying to make this obvious because the guy tried to sell it to me as a genuine item. Anyway.. I have spent about 10 hours polishing the runners in the manifold because I wasn't happy with the casting finish. I never tried to port it bigger, I just took enough off to make the surfaces smooth as.

Asking $600 ono for both

Sorry if this is a silly question but is this is for RB25DET?

Link to comment
https://www.sau.com.au/forums/topic/172673-sold/#findComment-3177537
Share on other sites
lrc135 Enthusiast

lrc135

Posted
  • Author
Posted

I bought these together so I didn't think of seperate prices. But since the manifold is $350, I will sell the throttle body for $250

Now dropping price to $550 for both.

Pics tomorrow maybe. I will try to borrow a camera.

Link to comment
https://www.sau.com.au/forums/topic/172673-sold/#findComment-3183530
Share on other sites
  • 3 weeks later...
lrc135 Enthusiast

lrc135

Posted
  • Author
Posted
;) polished inside :P

Polished internal runners cause fuel to form droplets which can result in idling issues. It is best to leave the inside of runners rough to prevent this from happening.

How can that be when the fuel is injected at the end of the runners right at the inlet face of the head. Fuel would not even touch the runners. All I have done is stop some turbulance buy removing shitty casting finishes. Had the casting been neat like the rest of the manifold I would not have cared.

Maybe it happenes with other manifolds but not this one.

Link to comment
https://www.sau.com.au/forums/topic/172673-sold/#findComment-3215817
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I see what you mean on that last paragraph and makes sense. I am leaning towards because I made the repair/filler area large that I didn't use a long enough block. Will minimise the area and let you's know how I go. This is random but I noticed when I put epoxy primer it felt flat but that's just temporary.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Tried to repair with filler only. The block is a foam block but quite hard and I put a velcro on it for sandpaper, the hook and loop system. It's not one of those super soft ones that just follow the panel. Similar to a dura block.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      You need one of those automated sprays that puffs a nice small every 15 minutes in their room. Except swap the nice smell for chloroform...
    • MBS206
      Vag Coil Diy loom wire guage selection

      By MBS206 · Posted

      Don't step down power supply size, maintain it the whole way. It's how I'd do it. OR, Id have one feed, with one joint that splits out to six smaller gauge wires that go to each coil. I wouldn't add joins like stepping from 12 to 16, at the first two coils, as if you try to continue that fashion, each joint will introduce a voltage drop. In theory, earths should be the same size as power feeds, however in this case the main power needs to be bigger due to the average size current. So the next question is, how much current do these coils actually need?
    • MBS206
      Steps to DIY sanding car back ready for respray....

      By MBS206 · Posted

      I think Murray is onto it. It's sounding like either it's a soft block, not long enough block, OR if you're chasing waves, you're going in the direction of the waves, instead of across them. Rotate your sanding pattern by 45 degrees is something to try. You said you're going in an X, so now instead, from the same perspective, do a "t" instead.   If you're not able to have the block sit on top of two high points, and not touch the low point between them, you'll never get it flat.
×
×
  • Create New...