Jump to content
SAU Community

Sold

Jago
 Share

Recommended Posts

Jago Mentor

Jago

Posted
Posted (edited)

Now also selling 2x S15 turbo injectors. $100 delivered/posted (check last post for more info)

Located in the Sutherland Shire, in Sydney.

If interested, PM me, post, or call 0401 874 604 (after 3pm).

Cheers,

Phil.

***SOLD***

Edited by Jago
Link to comment
https://www.sau.com.au/forums/topic/175653-sold/
Share on other sites
Jago Mentor

Jago

Posted
  • Author
Posted (edited)

hmm, perhaps the stupidly cheap prices are scaring people off? :w00t:

The adaptor plates convert stud pattern to RB26 exhaust manifold stud pattern, can use any RB26 manifolds with these puppies on. Turbos are in good condition, NEVER gone past 13psi, uses braided oil lines and high quality water lines and fittings.

Not a dodgy backyard slap together, setup isn't as laggy as you'd think either, people have been known to use laggier single setups on RB20's. Kit made ~200rwkw on only 13psi.

Need it all gone people :dry:

(if stud pattern on RB25 is the same then can obviously use this for it too, im not too familiar with the stud pattern)

Edited by Jago
Link to comment
https://www.sau.com.au/forums/topic/175653-sold/#findComment-3224095
Share on other sites
  • 3 weeks later...
abu Grand Master

abu

Posted
Posted (edited)

PM sent.

I want to know if its plug and play into the R32 ECU or is it a universal unit which needs to be wired up?

Does it have a plug where it plugs into the MICROTECH unit, then another plug on the other end? Or does it just have lose wires? :ermm:

Or if you dont know can you just send me pictures of the loom, I will be able to let you know.

Sorry for the big post. :P

Thanks,

Abu

Edited by abu
Link to comment
https://www.sau.com.au/forums/topic/175653-sold/#findComment-3303619
Share on other sites
Jago Mentor

Jago

Posted
  • Author
Posted

comes with a complete wiring loom which plugs right into the microtech. It's not a bundle of loose wires. It doesn't plug into the standard unit, it is a complete replacement ECU. Will email pics if you need them

Link to comment
https://www.sau.com.au/forums/topic/175653-sold/#findComment-3303658
Share on other sites
abu Grand Master

abu

Posted
Posted (edited)

I have attached a picture of the MICROTECH that Phil is selling to help him with his sale.

This MICROTECH comes with loom to SUIT R32. This means that there is no wiring required, just plugging in the plugs as the loom has all the plugs ready to plug into the existing sensors and injectors. Pretty much plug it in and get it tuned and off you go.

The installation can be done by your self, so there is no need to get a tuner to install it. Its pretty straight forward.

2nd closest thing to a plug and play unit pretty much. It should also hold a base map for a RB20DET.

It is very well priced, and is a complete stand alone ECU. Also comes with the in-line hand controller for real life readings and tuning, which brand new is worth about $200.

Don't miss out on it if you are looking for a full standalone after market ECU, its very worth it IMO.

Phil didn't know much about the ECU so I am just helping him out with the sale, nothing in it for me.

Good luck with the sale Phil.

Thanks,

Abu

post-11894-1187776076_thumb.jpg

Edited by abu
Link to comment
https://www.sau.com.au/forums/topic/175653-sold/#findComment-3304113
Share on other sites
Jago Mentor

Jago

Posted
  • Author
Posted

In regards to the 25, I'm not 100% sure on that, never was too sure, you'd have to check up on it yourself. But as mentioned before, and as shown in the pic, it does come with the loom. You'd need to re-tune it regardless of what motor/setup you are running it on.

As for Auto RB20, same deal. I'm not a tuner, I'm just selling what I had one my car ;).

Link to comment
https://www.sau.com.au/forums/topic/175653-sold/#findComment-3311440
Share on other sites
  • 2 weeks later...
Jago Mentor

Jago

Posted
  • Author
Posted (edited)

bump.

Also adding 2x S15 turbo injectors. 444cc/min, direct replacement/fit to an RB25. All you need to do is go buy yourself another set of 4(common enough) on ns.com or something and bob's your uncle, upgraded injectors.

$100 posted

Also, please don't message/pm me/contact me and say you are going to pick up blah blah blah and never be heard from again. Stop wasting my time.

Edited by Jago
Link to comment
https://www.sau.com.au/forums/topic/175653-sold/#findComment-3327246
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Borci88
      Borg Warner EFR Series Turbo's V 2.0

      By Borci88 · Posted

      Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • Chocolate Cheesecake.
      Infiniti Q60 Navigation Update

      By Chocolate Cheesecake. · Posted

      I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Luckily I didn't put in etch primer as I just found out it's not compatible with my body filler lol. Also just need to sand the panel anywhere between 150-400 grit so I'm in the clear there. It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Yep will do, thanks for all the help.
    • itsforandres
      BCNR33 Blower Motor Resistor - Testing

      By itsforandres · Posted

      @dbm7 and @GTSBoy thank you both very much! will give that a shot!
×
×
  • Create New...