Jump to content
SAU Community

Getting tight bolts off

PLAYAR

By PLAYAR,
in General Automotive Discussion

 Share

Recommended Posts

deesh Collaborator

deesh

Posted
Posted

If you just pull then they will break off, i know at least two other people who have learnt this, and they know who they are.

The tip is to use short sharp jerky pulls/hits with the palm of your hand, and most of the time they will let go.

WD40 or similar is also a good idea.

Doctor Mentor

Doctor

Posted
Posted

Same thing happend to me and is still happening. Tried to get one of the bolts off. The bolt started to beark to peices but the main section that is round is still attached.

Ever tried putting on lowered springs with out taking out the suspension? Not very fun at all.

I'm going to grind the bolt off.

Doc

slip Mentor

slip

Posted
Posted

Single hex sockets/spanners are great when you're up against a c*nt of a bolt.

If its going to break, youll probably be able to feel it, when you get to this stage you might be a bit screwed.

use leverage but make sure the tool is still on the head realy good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...