Jump to content
SAU Community

Recommended Posts

Hey everyone, after many weeks of stressing whether or not I should do it I came to the conclusion it would be best for me and the car to part. Main reason is new job is in St. Leonards so train is the only option, the car has been sitting collecting dust when i finally finish all my hard work with it. Another reason is because im big on the beach and really need a beach beast to go camping and beach driving with.

This car was featured in the SAU Autosalon display, it is an excellent example of a R33 with sensible yet noticeable modifications. It drives like an absolute dream and is very quick. I have owned the car for a bit over a year, since then i've only put about 11000 or 12000kms on it. Never EVER had a problem with this car you will be amazed its a 1993 make. Car is in immaculate condition you need to see to believe. Car has been garaged every night unless out at my gf's. I have receipts for EVERYTHING done to this car.

Also comes with the plates FR-33-SM (not shown in pics)

OTHER POINTS ABOUT THE CAR:

* Has slight damage on rear bar from tapping a brick wall (this is what happens when mum drives your car). Will be speaking to my mate who will repair this.

* Car has July 2008 Registration

DETAILS:

1993 Nissan Skyline GTS25T with 101,000kms on the clock (major 100,000km server performed 12,000kms ago when I bought it).

Factory paint colour

MODIFICATIONS:

3" Xforce Turbo back exhaust

JustJap FMIC

Splitfire Coils

Bosch 023 fuel pump

Apexi POD with heat box (nice and legal) (still have the original box if needed)

GFB Mach1 BOV (got the factory bov handy)

NGK Iridiums

Gates Heavy Duty Timing Belt

Bleed valve running 11psi (i know dont shoot me. never got around to getting a proper electronic one)

ECU remap performed by Toshi from this forum

* All engine work and seats were done by Greg at Autosport, Kirawee.

last dyno run was 174rwkw without the remap and car was suffering from boost cuts. Now no more boost cut and ALOT more power from the remap.

EXTERIOR:

GTR frontbar

GTR grill

400R side skirts

400R rear pods

400R rear wing

Jetspeed eyelids

19" MATRIX rims (only 6 months old great tread)

INTERIOR:

$3000 worth of SONY audio gear all under warranty (i'll keep speakers in car but will take the head unit out, cost me $800 new)

JustJap bucket seats

TV screen in one of the DIN's (currently used for the carputer)

Probably the cleanest interior you'll ever see. the dash looks brand new.

* All audio and video gear was installed by Cronulla Car Sound

PHOTOS:

Please note that most of these photos were taken BEFORE i got the new grill. The first AutoSalon picture shows the new grill. Will take some pictures on the interior in day light.

Copyofmycar_stock.jpg

P4010037.jpg

P4010035.jpg

P4010026.jpg

P4010017.jpg

P4010006.jpg

P2020004.jpg

IMG_4377copy.jpg

PRICE:

Will consider offers. Not sure on the price however I am in no rush to sell. Still awaiting to find my beach / camping beast.

Very reluctant :) sale but someone will enjoy this car as much as I did and hopefully go further with it.

Link to comment
https://www.sau.com.au/forums/topic/176645-fs-r33-gts25t-sold/
Share on other sites

  • 4 weeks later...
  • 1 month later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...