Jump to content
SAU Community

Recommended Posts

I get asked quite often how to tell if second hand shocks are OK. While it is not 100% perfect, you can do some easy checks, if any of these show a problem then its rebuild time.

1. The first job is to check for oil leaks around the top seals, on the shock body where the shaft goes through. Any oil (even a tiny bit) is bad news.

2. Next make sure that the shocks have equal gas pressure, take the springs off and compare the front pair with each other. Push them down equally and make sure that it takes the same amount of force to push them down. Any difference (even a tiny bit) is bad news.

3. Then make sure that they come up together at the same speed. Any difference (even a tiny bit) is bad news.

4. Do the same for the rear pair.

5. Lastly look at the shock shafts, if they are not perfectly shiny, the same all the length and all the way around, then that is real bad news. They must have no rust, no scratches and no visible wear marks. New shafts cost more than whole shocks.

That's about it, if the shocks pass those tests then chances are they are OK, for now.

:D cheers :)

Link to comment
https://www.sau.com.au/forums/topic/176989-used-coilovers/#findComment-3234884
Share on other sites

I did all the above steps stated when i bought some used coilovers a while ago but turned out that the pillow ball mounts were all worn out and knocking it's head off.

What i feel is that, you have no way to tell whether used coilovers are good or not until you actually fix them onto your car and drive them.

Link to comment
https://www.sau.com.au/forums/topic/176989-used-coilovers/#findComment-3235183
Share on other sites

I did all the above steps stated when i bought some used coilovers a while ago but turned out that the pillow ball mounts were all worn out and knocking it's head off.

What i feel is that, you have no way to tell whether used coilovers are good or not until you actually fix them onto your car and drive them.

I wrote the above in the ShockAbsorber 101 thread in answer to a question on how to tell if used SHOCKS are OK, the additional test for strut tops are;

1. If they have spherical bearings then there is a 99% chance that the bearings are stuffed, so check them carefully.

2. Remove the strut tops from the shock/spring unit and rotate the spherical bearing, check for scuff marks and wear through the hardening. This shows up as discolouration and sometimes even surface rust.

3. Bolt the strut tops back on the shaft shaft (without the spring), then check for play by rocking the strut top while holding the shock solidly (in a vice is best).

4. Any free play, visible wear or knocking means that the spherical bearings are stuffed, this usually means buying new strut tops as most Jap coil over kits use unique sizes of sphericals.

If the guy selling them won't let you do the above tests (plus the shock testing) then WALK AWAY, they are most likely useless.

;) cheers :D

Link to comment
https://www.sau.com.au/forums/topic/176989-used-coilovers/#findComment-3236228
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
    • Is it alright to top up with just another green coolant?
×
×
  • Create New...