Jump to content
SAU Community

Recommended Posts

hey,

well i was going to buy some whiteline sway bars but the thread started on here wont get back to me so im going into autobahn tomoro to buy some. I was just wondering what size is best for drift... ive been told thick front good and slightly skiny rear and good traction.... but if i want to set up car for drift is fat rear good??

ANyone recommend some thicknesses for r32 gtst 4 door for front and rear whiteline sway bars.

thanks

Link to comment
https://www.sau.com.au/forums/topic/179657-sway-bars/
Share on other sites

actualy autobahn are $20 more expensive each than SK but i need these urgently.. Im going in today to sort things out with them. I know a few guys who work there so i get it fairy cheap. I dont know about saving $60?? I know commodores are cheaper to buy for than skylines so maybe u have a diff make of car... i dont know... maybe you got lucky.... but me mate told me he cant do them for $189 cause thats prettymuch what they pay after they have it delivered to thre store.

Anyways... i think i might get the fattest ones i can.. thanks guys

Link to comment
https://www.sau.com.au/forums/topic/179657-sway-bars/#findComment-3272734
Share on other sites

If the autobarn guys can't guarantee that the bars will have minimum 3 hole adjustment (they usually have 2 hole these days) then get 24mm front, 24mm rear. It will be the only way you can balance the car.

If they are only 2 hole then you will need to set the front on hard and the rear on soft and that should be fairly balanced. If you want the thing more taily then put them both on hard.

If you go bigger on the front without the 3 hole (minimum) adjustment either end then you will not be able to dial out the understeer.

Link to comment
https://www.sau.com.au/forums/topic/179657-sway-bars/#findComment-3273676
Share on other sites

Swaybars are the single best enhancement you can do for the handling of your car. They essentially link the sides of your suspension and minimize the body roll, which means your car handle much better through corners.

Make sure you buy adjustable swap bars. Adjustable bars allow you to tune in or out understeer/oversteer as required. The incremental cost of adjustable bars over non-adjustable is minimal for what you get in return.

Link to comment
https://www.sau.com.au/forums/topic/179657-sway-bars/#findComment-3280935
Share on other sites

For skylines, 24mm front and 22mm rear seem to work best with normalish spring rates for street use.. Swaybars work well because they simply have the least downsides for controlling roll compared to the other methods like springs (lose compliance) and low speed bump (lose midcorner grip).

Edited by salad
Link to comment
https://www.sau.com.au/forums/topic/179657-sway-bars/#findComment-3281488
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...