Jump to content
SAU Community

Replacing Starter Motor Rb20

OnAhigh

By OnAhigh,
in General Maintenance

 Share

Recommended Posts

OnAhigh Experienced

OnAhigh

Posted
Posted

Hey guys im attempting to change my starter motor this weekend. Not very familiar with rb20 engines but i do have some knowledge on mechanics. Is it a easy enough swap over? can it be done by the backyard mechanic? lol is there anything i should know about that will save me from cursing all morning? tips/help/advice

thanks in advance

Dave

Link to comment
https://www.sau.com.au/forums/topic/180863-replacing-starter-motor-rb20/
Share on other sites
soslo_31 Enthusiast

soslo_31

Posted
Posted

disconect your battery to start of with

it preety easy to do you will need a 12mm spanner and 14mm spanner 10mm spanner for battery

all you do is disconect batt, remove wires on starter one will be a 12mm nut and the other will be a push on wire

undo two 14mm bolts and pull it out

and install is reverse just make sure yoou compare your old one with new one to make sure there the same

it is preety tight to get your hands in there but shouldnt take you any longer than a hour to do it.

and its easyer from the top than the bottom

OnAhigh Experienced

OnAhigh

Posted
  • Author
Posted

well gave it ago today, with no luck, and the short spurt of rain didnt help either lol. I just couldnet manage to undo the one bolt. managed to get the bottom one off piss easy but the top one, couldnt get my hands or a spanner in there. is there a special shaped spanner or socket piece i could you to squeeze it in there?

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • joshuaho96
      Ethanol Content Sensor - Always at 11%?

      By joshuaho96 · Posted

      The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...