Jump to content
SAU Community

Gtr Turbo Water Lines

JimX

By JimX,
in General Maintenance

 Share

Recommended Posts

JimX Grand Master

JimX

Posted
Posted

Does anyone know the part number for the hose in this pic (marked in red), or if I can get an aftermarket one from Autobarn or somewhere? The hose says Nissan 54TS on it. Also are there any others that I should be aware of that I may as well replace at the same time? Heater hoses or the like? There is one more short hose on the left out of the shot that I will also replace. The 2 main large radiator hoses are fairly new but the rest have probably never been replaced.

post-502-1187496356_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/181472-gtr-turbo-water-lines/
Share on other sites
GTRgeoff Grand Master

GTRgeoff

Posted
Posted

Get normal hose mate and use a hose coil, like a spring fixed to a piece of thin flat steel, to get the shape without the hose kinking. Should set you back about $10 all up. Bursons have the hose coils.

Syphon Rising Star

Syphon

Posted
Posted

Have a look at the attached picture.

If it is the highlighted part that you are talking about the part number is 14055-05U21

Also the other small hose you talk of which is marked in that picture as 14056VB, the part number for it is 14055-05U22

Best of luck

post-642-1187507743_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...