Jump to content
SAU Community

K&N Pod Filter Question


Recommended Posts

Guest RedLineGTR

About a month ago purchased a k&n pod filter for my r33 gtst...recently it seems to be loosing it colour....some of the corner are going white...i have the recharge kit and have noticed that the oil that you treat the filter after you wash it, is red..

Since i only purchased the filter a month ago or so, would the colour of just faded away abit from the engine temps if so i assume that the oil is still in the filter element only the colour has faded away..??

Link to comment
https://www.sau.com.au/forums/topic/18273-kn-pod-filter-question/
Share on other sites

Guest RedLineGTR

1. disconnect your AFM from the pipe that leads to the turbo

2. unbolt the airbox (if its still there) so that the piece conneted to the AFM is loose

the afm and half the airbox should come out together

3. get some break caliper cleaner/ electrical contact cleaner from supercheap auto

4. hold the AFM upright and spray in small bursts into the AFM onto the element which you should be able to see. don't use too much - keep it for next time

5. let it dry (should not be long) and reverse the order you did to take it out to get it back in

your AFM is clean! now all you have to do is reset the ECU and your right as rain! (Sometimes the reset helps more accurate calculations)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...