Jump to content
SAU Community

Recommended Posts

Don't count on it finishing at 10pm, get down there as early as you can.

WSID has a habit of finishing nights early if only a few competitors turn up (take wicked wednesday 2wks ago as an indication). They want 300 cars doing 2 runs each all paying money instead of 50 cars doing 25 runs each having a good time.

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Don't count on it finishing at 10pm, get down there as early as you can.

WSID has a habit of finishing nights early if only a few competitors turn up (take wicked wednesday 2wks ago as an indication). They want 300 cars doing 2 runs each all paying money instead of 50 cars doing 25 runs each having a good time.

Bastards! Ill be there when gates open..

All i need is a helmet?

I so want to see what my car will do on track!

Has anyone got any cheep ideas helmet wise?

You need a helmet, long sleeve shirt/pants, rego papers - it's all on the WSID website.

Cheapish helmets are available for around $100-$150ish upwards from Motorcycle Accessories warehouse on Church St, Parramatta. There are other places you can go if that's not local for you. Do a search on the forum, there's been a few threads about helmets etc before.

I'm starting to regret going away for the weekend lol. Would've liked to take the car out for a run again :)

I'm starting to regret going away for the weekend lol. Would've liked to take the car out for a run again :P

I'm happy to give it a run for you if you want, forget about the fact that my last time on track cost me over $15k it's all about having fun and getting that timeslip right...

Do you expect anything less from them?

I'm in also.

uh oh... stay away from my tools!

I have stronger ones now so you can't break em anymore! ha ha

K im in ... picking up the new car at 10 .... drive straight to WSID to see if I can break it :P

Don't count on it finishing at 10pm, get down there as early as you can.

WSID has a habit of finishing nights early if only a few competitors turn up (take wicked wednesday 2wks ago as an indication). They want 300 cars doing 2 runs each all paying money instead of 50 cars doing 25 runs each having a good time.

Ill be spectating for a bit (work permitting), ill bring a broom and sawdust for you Ben

uh oh... stay away from my tools!

I have stronger ones now so you can't break em anymore! ha ha

K im in ... picking up the new car at 10 .... drive straight to WSID to see if I can break it :whistling:

I hope your new tools aren't made in China :laughing-smiley-014:

I will be just spectating, but I don't like the chances of the event actually being on.

Ill be spectating for a bit (work permitting), ill bring a broom and sawdust for you Ben

No need, im a spectator at WSID these days... limited myself to just eating hotdogs, not as expensive but just as deadly as exploding flywheels :whistling:

I hope your new tools aren't made in China :laughing-smiley-014:

I will be just spectating, but I don't like the chances of the event actually being on.

lol... nope all Kinchrome with lifetime warranty just in case you need them :)

Hmmm yeah forecast doesn't look good...... :blink: *does anti rain dance*




  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...