Jump to content
SAU Community

Recommended Posts

Hey u goin guys planning on takin my skyline back 2 calder this fridai nite went last time with 3"inch turbo back and front mount air filter ( no heat shield or cold air induction) and a boost controller not EBC ran a 14.3 at 100.2 MPH now i dont know if thats shit or decent or wat for a r33 series 2 was hittin around 9-10psi , now ive got a greddy profec B spec II in and a full 90mm cold air innduction ran should i b looking for better times? if so roughly wat with decent take off and gear changes

Link to comment
https://www.sau.com.au/forums/topic/183800-14-mile-return/
Share on other sites

what was your 60' time?

aroun 2.0 is good, 2.2 is average and can be improved upon.

without sounding slack, 14.3 is not a good time.

9-10 psi in a stock ECU'd r33 means it would be running pretty rich and on the edge of misfiring and carrying on.

cheapest way to get better times (apart from practice) is a tune with an SAFC to fix the air:fuel mixtures.

obviously some street legal drag radials.

then practice away.

maybe list any other mods.

what:

wheels and tyres and what size are they

what tyre pressure?

clutch

do you know what power it is making?

Link to comment
https://www.sau.com.au/forums/topic/183800-14-mile-return/#findComment-3328903
Share on other sites

Hmm thinkn runnin back 2 standard boost on the nite , dunn have a clue power havnt had it tuned or dyno'd standard 16"inch wheels and standard clutch...like it hits around 7 then the boost slowly creeps up 2 around 9 on higher revs

2.303 60"

tyre pressure was around 28 psi for the nite from memory

Link to comment
https://www.sau.com.au/forums/topic/183800-14-mile-return/#findComment-3328912
Share on other sites

Hey u goin guys planning on takin my skyline back 2 calder this fridai nite went last time with 3"inch turbo back and front mount air filter ( no heat shield or cold air induction) and a boost controller not EBC ran a 14.3 at 100.2 MPH now i dont know if thats shit or decent or wat for a r33 series 2 was hittin around 9-10psi , now ive got a greddy profec B spec II in and a full 90mm cold air innduction ran should i b looking for better times? if so roughly wat with decent take off and gear changes

just to give you a rough idea, my younger bro has a r33 gts-t series 1.5, stock turbo and engine, stock ecu (no SAFC), boost at 12psi, full exhaust, FMIC and a pod, pulled a 13.3 with a 2.0 60 foot time.

You should easily crack a high 13 with you mods if you launch it right and drive it hard.

Link to comment
https://www.sau.com.au/forums/topic/183800-14-mile-return/#findComment-3329349
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
×
×
  • Create New...