Jump to content
SAU Community

Recommended Posts

i have some left over bits for a r33 gtst

1 x series 1 passanger seat complete $80

1 x boot lid $50

2 x back seat side panels $25 each

1 x complete back seat $60

1 x bottom back seat $30

2 x full set up seat belts $80 each set

2 x complete rear ends inc brakes rotors diff cradle the lot $300 each (will seperate)

1 x front end parts cross member/control arms/steering rack/stablizer bars $200 lot

1 x rear garnish clear type 2 broken clips i think $15

1 x fuel cap nissan $15

1 x fuel lid $15

1 x manual tailshaft $120

1 x trust rear wing fibreglass $100

1 x series 1 rear wing $40 with light

4 x pairs of drift rims to suit 5 x 114.3 skyline $60 - $80 pair

4 x pairs of dfift rims to suit 4 x 114.3 180sx Silvia $40 - $80 pair

1 x handbrake lever unit $15

1 x roof light $15

1 x pair of sunvisors $15 need clean

1 x drivers seat has tear on cushion $25

1 x ignition barrel no key $20

1 x steering column $40

all these parts are located in keilor in western suburbs of melbourne please call me on 0402090079 if u wish to ask anything or buy something

All prices nego

post-10006-1190706963_thumb.jpg

Edited by SXC_R33
Link to comment
https://www.sau.com.au/forums/topic/186437-r33-gtst-bits-heaps-need-room/
Share on other sites

hey mate you havent got front slotted rotors by any chance do ya? also can you send me a coupla pics of all the rims to bloodsword27@hotmail.com please? might end up taking all of them, can i get a better price?

  • 2 weeks later...

when you get a chance pics for 4 x pairs of drift rims to suit 5 x 114.3 skyline $60 - $80 pair

4 x pairs of dfift rims to suit 4 x 114.3 180sx Silvia $40 - $80 pair please

when you get a chance pics for 4 x pairs of drift rims to suit 5 x 114.3 skyline $60 - $80 pair

4 x pairs of dfift rims to suit 4 x 114.3 180sx Silvia $40 - $80 pair please

+1

please... pics of rims... if the 4 stud 17" ones look ok i WILL buy them. i just don't want to drive all the way out to keilor if i don't like them

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Like I said, "black magic" LOL In the end,  it is what it is, and hopefully, what this here knuckle head has done is an improvement and not a hindrance Not that I actually notice any negatives now, or that I will get any seat of the pants benefits when all is said and done, but best practice says I shouldn't be pulling intake air from the hot engine bay  Famous last words: I cannot see it being any worse than what it is at the moment 馃
    • If the gases flowing in those two tracts had the same properties, you could maybe use such broscience. But the exhaust has a different composition, different normal density, different actual density (because of different normal density, and mostly because of the massively higher temperature), and different viscosity (again because of much higher temperature). Consequently, all of the fluid dynamics parameters that matter, that you calculate from these inputs, such as the Reynolds number, friction factors (for wall friction) and so on, are all incomparable.
    • And we shall have to presume that Canada is the same?
    • In the US almost everything is E10. It can't exceed 10% by much or fuel systems have trouble adapting. At the same time because MTBE, MMT, and TEL are all banned they need as much ethanol in it as possible to boost octane.
    • I was mostly jesting. In my experience (and probably only my experience) the R34 GTT physical airbox space is actually too small to flow the amount of power it wanted. By sealing the box, I made it so it could only be fed by the ducts themselves. So you can seal it up and get nice cold air which IS good, but at a certain crossover point: More Hot Air > Less Cold Air I don't think you're at this point. In my case merely ducting the hot air intake with a very focused set of ducts counteracts the fact it's in a V8 engine bay. More cold air obviously best. The solution looks great.
  • Create New...