Jump to content
SAU Community

Recommended Posts

Need some advice again.. :P

Got some strange sound (continuous relay ticking) coming from the ECU when on boost (no sound when boost is below 0 psi) . When i turn off the AVCR, the sound gone.. so i need a AVCR expert to help me out... Where can i find them...? :D Can anyone point me to the right direction please..!!

Link to comment
https://www.sau.com.au/forums/topic/186695-apexi-avcr-dyno-tune-expert/
Share on other sites

Silly question, it's not coming from an electronic boost controller solenoid is it?

NO Marc, came from the ECU inside the car.... the Boost controller solenoid was installed near the air intake..

From your ECU did you say ? sounds like ur wiring to remove boost cut / control (factory one) isnt working properly .. if u want a quick check take it to Centrex sunnybank or Godzilla mark did my SAFC neo tune .. hope it works out

From your ECU did you say ? sounds like ur wiring to remove boost cut / control (factory one) isnt working properly .. if u want a quick check take it to Centrex sunnybank or Godzilla mark did my SAFC neo tune .. hope it works out

ok thanks Vish.. Any idea how much they charge ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...