Jump to content
SAU Community

Recommended Posts

Hey guys, i was just wondering i'm here in rainy melbourne and i dont do it often but sometimes if there is an a wide open road with a highly visable corner i'll play drift.

My amature technique is to hold the clutch in 2nd or 3rd, give it a bit of revs and let her rip whilst throwing a bit of opposite lock, it works a treat.. but there must be other ways of setting up a drift?

I was also wondering does anyone in Victoria hold drift track days, i'd like to practice more on a track rather than on the street.

And lastly are the skylines easy drifters?

cheers

Anthony :)

Link to comment
https://www.sau.com.au/forums/topic/1868-drifting/
Share on other sites

  • 2 weeks later...

Depends what sort of skyline you mean. 32's seem to be pretty good, not many people drift 33's are they're pretty heavy, and no one really drifts 34's cause they're so expensive.

That doesn't mean it can't be done though.

That's pretty much the easiest way to drift, if it's a really big wide long corner, just hit it at pace and turn hard, if it's wet the bum should come out a bit and spin the wheels and the car will come sideways. I don't know about Victoria, but we had a skidpan day up here recently, my car was broken and I couldn't go :) but that's basically all the day was.

Link to comment
https://www.sau.com.au/forums/topic/1868-drifting/#findComment-41530
Share on other sites

Guest Simon-MrRx7

acctualkly its safer in the wet.. easier to break traction therefore speeds are lower, if u loop it u just usually spin out in ya own car length..

when its dry your pushing it harder and faster... if u loose it.. cange are u gonna hit something harder.

Wet is also better for tyres :)

i was once getting a new set of rear on my rx7 every 2nd week :(

Link to comment
https://www.sau.com.au/forums/topic/1868-drifting/#findComment-42444
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...