Jump to content
SAU Community

Where Is The Best Place To Attach Pfc Hand Controler !

greyshoes

By greyshoes,
in Exterior & Interior Styling

 Share

Recommended Posts

greyshoes Rookie

greyshoes

Posted
Posted

I had my PFC hand controller lying everywhere from the gear shaft to the little pocket bin next to the cigaret lighter. Sick of it. Now I want to stick it up somewhere that I can easily see like the empty place next to the anttena switch so that the screen can be seen just below the fuel meter, that way I dont need to move my head everytime I have a look at it. But the freaking plastic panel can not be sticked with any kind of tapes. And I'm about to go to my last option which is super glue. But it's really sound stupid to me. Anyway, u guys have any ideas how to stick it up or any others place to hang it so we can easily see it when we drive. Turning head and look at somewhere else but not ur front screen is really dangerous. Cheers,

Lazy-Bastard Grand Master

Lazy-Bastard

Posted
Posted
Tried velcro tape?

+1

Use 2 pieces of Velcro for extra rigidity.

N.B. The adhesive backing on the Velcro may remove that stupid rubber coating from your dash surround if you ever take it off.

http://www.skylinesaustralia.com/forums/up...-1176971154.jpg

greyshoes Rookie

greyshoes

Posted
  • Author
Posted

Hey man, I think mine surround dash board different than yours coz the plastic on mine one is so rough that you couldn't glossy surface at all. I still can see the reflect from yr dash board surround. Pics will be put tomorrow.

75coupe Grand Master

75coupe

Posted
Posted

just to the left of steering column it'll cover your fuel gauge slightly but you don't want to be reminded how much fuel you just used so its better to hide it alittle...

make sure you clean down the surface with metho to get any shite on their velcro tape is what I used, you just want to make sure you get the best adhesion possible....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...