Jump to content
SAU Community

Recommended Posts

Thanks again for info.

I had the (nasty, as it turns out) wheel bearings pulled this week, and a new set pressed in yesterday. Im going to reattach the rear trailing arms ASAP, and then reassess the situation. If things STILL aren't running smoothly the valves are next on the job list.

  • Replies 63
  • Created
  • Last Reply

Top Posters In This Topic

Ok... I took the car to the NSDOC show and shine and it actually made it there in one piece! It got a good run later that day and went well, but I still think the car is falling short of its full potential.

At the moment the grinding from the rear has gone; clearly the wheel bearings were absolutely cactus, and brake pedal pressure is good. I am yet to try experimenting with different proportioning valves, but if things go well over the next while I may not need to.

The engine is also going much better than previously, but the power still seems to drop off a little too early, around 5,500 rpm - pushing on to 6,000 rpm and above just seems to upset the old girl. I am acutely aware of this because on the few good runs that I have had over the last year she would scream up to 7,000 with no signs of resistance. Something just isn't quite right.

Next up I'm going to move the electric fuel pump to the rear and insulate the fuel lines with heat-resistant wrap to see if that makes any difference.

(many thanks go to Blind Elk for the tips and the chat on the weekend).

Ok... I took the car to the NSDOC show and shine and it actually made it there in one piece! It got a good run later that day and went well, but I still think the car is falling short of its full potential.

At the moment the grinding from the rear has gone; clearly the wheel bearings were absolutely cactus, and brake pedal pressure is good. I am yet to try experimenting with different proportioning valves, but if things go well over the next while I may not need to.

The engine is also going much better than previously, but the power still seems to drop off a little too early, around 5,500 rpm - pushing on to 6,000 rpm and above just seems to upset the old girl. I am acutely aware of this because on the few good runs that I have had over the last year she would scream up to 7,000 with no signs of resistance. Something just isn't quite right.

Next up I'm going to move the electric fuel pump to the rear and insulate the fuel lines with heat-resistant wrap to see if that makes any difference.

(many thanks go to Blind Elk for the tips and the chat on the weekend).

Was that you getting around in the Nissan Shirt?

Ill try and get some pic's up soon

Was that you getting around in the Nissan Shirt?

Ill try and get some pic's up soon

Yep, black T-shirt with a Datsun logo. I was looking out for your 240k's. Did you come with a different car?

Ill post up some pics this evening under the NDSOC post.

He was driving one of my R31's, the fire brigade one.

Hi, I'm sure I know who you guys are now, sorry I didn't introduce myself on the day.

Your R31's were lovely by the way!

You know who we are now, so next time come up and slap us on the back like we're old mates lol.

I did like your car BTW. Carbies, and several of them is always very cool.

I love my 31's thanks for the compliment.

Hi, I'm sure I know who you guys are now, sorry I didn't introduce myself on the day.

Your R31's were lovely by the way!

we did have a good chat, i told you about the other car @ center rd, lol, im k's are off the road at the moment :D but soon i hope ill have one up and running

we did have a good chat, i told you about the other car @ center rd, lol, im k's are off the road at the moment :O but soon i hope ill have one up and running

Ahhh! (Slaps forehead) it all comes clear now. Im going to have a look at centre rd probably this week. Good luck with the K's by the way.

there was one in the back of an old warehouse, had flames across the bonnet etc... it was on ebay a year or so ago...

it looks like drew may have bought it as spares??? i dunno

but i have heard they creak and sag a whole lot as the supports are gone from the roof etc.

yeah would be pretty weak, but would be nice to see one.

have seen a couple pics of an R31 Convertable, only 2 were ever made... well by Nissan anyway.

Hi,

Yeah, a mate picked it up to use as spares. It looks ok from a distance, but when you get up close its just a 4 door with the roof crudely cut of and the rear doors welded up! A guy was using it to belt around on his farm!

Good news: I located the source of the grinding noise from the rear. One of the calipers had a lot of play in it. By reefing on the handbrake cable you could see if flopping around. An easy fix!

Bad news: I relocated my fuel pump to the rear, but the car still cant be pushed past 5,000 rpm. Grrrr... I got more out of my L24 running a single carby! Looks like I'll have to see a specialist. Some of the guys and the NSDOC show and shine were squeezing out triple the horsepower that I make from their L series engines.

I haven't forgotten about the mr30 "coupe", Ill get some pics etc up tomorrow.

D

Errr... Took the car to Nissco to try and find out what is draining the power so badly. The consensus is... wait for it... Carbies! That's right, the $1500 rebuild that I am bitching about in the title of this thread is the culprit. The needle and jet setup is wrong, causing the car to run way lean. About 18-20 to 1 air fuel mixture, as opposed to the ideal 13.5 to 1. So now I have to go back to the carby specialist, to ask him politely to sort it out... or Ill be forced to throw a stick on his roof.

I fixed the crappy caliper though.

Interestingly, the rest of the car came back with a fairly clean bill of health.

Anyway here are some pics of the mr30. Mags, you are welcome to come and get the spoiler (which is fairly convincingly attached to the boot) and the glass if you still are interested.

post-26626-1197623785_thumb.jpg

post-26626-1197623911_thumb.jpg

post-26626-1197623974_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...