Jump to content
SAU Community

Recommended Posts

Hi guys I need a r33 interior wiring harness diagram can someone help on this one?

If not this is the wirings that I need to find the colors code:

door's sensors=driver and passanger side?

sunroof ( the connector is on the driver's side up in the right corner but I don't know the wiring colors=?

interior lights=?

seat belts (driver and passangers f&r)=?

taillights brake signal=?

hazards=?

reverse lights=?

Just tell me the wiring's color for one of the things mentioned will be really good for me to try to finish my project!

Thanks for any help!

Link to comment
https://www.sau.com.au/forums/topic/188162-r33-interior-wiring-diagram/
Share on other sites

yes I have reading almoust everything and looked in a lot of fsm and I couldn't find it!

It's not for radio it is to make everything to work, I got a r33 front clip and I've installed and customed a lot of thing so I need to know these things to finish my project!

yeh i need an interia loom wiring diagram too been looking for like 3-4 weeks and havent found one, i'd be happy to buy a manual but i've got a couple that i downloaded and they dont have the interia loom on them only accessery ones and the ebay ones seem the same so i dont wana buy one that doesnt have it n i dont think haynes or gregory make them for skylines grrr

I'm about to finish the interior lights and some more things like sunroof and more... so as soon as I finish it I won't mind to post pics and specs here!

But if some one can take a copy from the fsm book and post here I'll be really happy.

Edited by dk_fabiosantos

Not yet!I still need it but most interior I found the hard way like: room lights are the wirings on the driver's side on the right top with a white connector with orange/blue (2 wirings) and one going to the back the same color orange/blue, I'll post the wiring pinouts soon with some pics.Right now I'm trying to find the power for the locks(I can't lock or unlock the dorrs and move the windows up and down too.)

What you need to know? I probablly know it.

And if you find it let me know please cause I have to find a lot of things still!

Thanks!

This is what I found:

fuel pump from cluster:

level- light= gray/red

low fuel light= light green silver pin

reverse light= red silver pin (coming from trans. sensor)

turn signals=

right side=green/yellow (hazzard is connect to this one too)

left side= green black

air regulator= blue silver pin (from air regulator located at the intake manifold and it is going to pin 5 on fuel pump relay.)

brake lights= pink/blue & yellow silver pin (coming from brake pedal sensor)

door's sensors= red silver pin (coming from black box "smart entrance".

There is the abs wiring harness on left side (pass. side) that I've disconnect all of them (one is ignition earth that I have found exactly for what is that.anyone know it?)

I don't remember the hicas right now but I'll post the wiring pin soon.

well i bought a burnt out shell cause i wrote off my old car and the shell has abs and airbags where-as mine didnt so when i swapped over the wiring i dont have any looms to connect the abs or airbags so im trying to do it custom i've done most of the airbags rather easily but the abs was almost completely burnt out so im not sure what wires go to where would be a lot easier to determin if i had a proper wiring diagram

I did the opposit of it, I've disconnected the abs and my car never came with airbag so I can take some pics of the abs wirings and tell you more or less where they go.

I've disconnected my abs from the fuse box (2 red wirings: one is all red and the other red/blue connected to a fuse), they go from the engine bay fuse box to a gray connector on the passanger side (near the pw sterring reserviol), then from the connector the abs actuator and I can't remember everything right so I'll try to post about it tomorrow asp, anyway at least you'll be able to connect everything (you'll be able untill the middle of the car,cause I had my front clip cutted right there in the middle!), I hope it is going to help you in some way!

well mines the oppisite lol, i've got the rear clip but not the front section of the wiring it was burnt up into the pasenger footwell everything from there back was ok, it would be greatly apreciated if you could post some pictures or if you in melb mabye i could come down have a look at it in person.

well mines the oppisite lol, i've got the rear clip but not the front section of the wiring it was burnt up into the pasenger footwell everything from there back was ok, it would be greatly apreciated if you could post some pictures or if you in melb mabye i could come down have a look at it in person.

Ya man for sure!I'll post the pics of it assemble but not in place cause it's really a pain in the a$$ to do man!

So I'll do that asp!

Edited by dk_fabiosantos

yeh thats cool dont have to be in place i can work that out any help is better than none, thanks for that, dont rush just when you get a chance i've still got lots of things to do on the car to occupy me before i tackle abs i've almost got the car startable but no where neer drivable.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...