Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

ok i changed the ecu still nothing its still a s1 ecu

with my motor i stripped all s2 electronic parts off it and put all my s1 parts on it

im pretty sure the motor was a s1 out of a auto stagea i just have no power at all nohting to dash lighst nothin ??

well thats what im trying to find is there any main power wire

its hard to find thinsga cause i have a greddy plenum on it now also

when i was charging the battery from under the boonet the dash lights came up with a real slow flash and a beep like when u leave your door open ???

but now there is nothing when i turn the key i get nothing

i cant see any more wires at all on both sides worst thing is i live in a country two 10 hours from sydney 6 form melb and 4 form adelaide so yer ................rooted??

sounds like a dead battery. You shouldnt be charging the battery with it still connected to the car.

Pull it out and give it a decent deep cycle charge (ie leave it on charge for at least 24hrs). Battery chargers charge at a very low ampage so it takes a while.

If its not that the battery its a main power connection thats not connected properly. Make sure your getting a good contact at the major areas like the battery terminals and the earth lines to the engine itself.

if you put the terminals on backwards i would say the main realy woulda blown but as long as you havent done that it should be fine, its designed to jump start the car so i couldnt do any damage just wont charge the battery effectivly

as mentioned b4 i think its cos you have a motor/ecu mismatch. the series 1 stageas were based on the series 2 r33 (rb25) and series 2 stags on the r34 (rb25neo). so if like you said you stripped all the wiring off and are trying to use the wiring from a series 1 r33 rb25 it wont work. you dont have an ignitor. find a series 2 r33 or a series 1 stagea ecu and try that

ill try a r33 series two ecu but what about my ignitor how do i get passed that ?? i have one and if i put a series two ecu in they dont have a sepreate ignitor

i still have the coil packs from the series 2 so i can put them in

i dont think it is the battery cause i had a jumper pack on and it still didnt go

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...