Jump to content
SAU Community

Recommended Posts

I need to sell my HR30. I never drive it as its a gas guzzler compared to my CRX.

At the moment I've got it for sale for $1600 NZD (around $1400 AUD). No one seems interested...

What do you lot reckon?

Thanks!

This is the for sale advert (56k be patient...):

1984 HR30 Nissan Skyline Sedan

White with black roof in tidish condition (VERY minor rust)

Front and rear bumpers could do with a replacing or refitting

33x,xxx km on Chassis (not sure about motor but its not that much!)

L20et with reconditioned head

New headgasket

New manifold gasket

New PCV Vavle

RB20det Turbo running 10psi

5 speed manual (box in GREAT condtion) with nice gearknob

GFB Boost Controller

New headgasket

New Thermostat

New Simota Oil Breather Filter

TCC Work BOV

RX7 Intercooler

Short and fat IC piping

Block and IC piping painted chevy orange recently

New Bosch Coil

Big Bore Exhaust

Century Marine Battery ($220)

Relocated AFM

Handbreak plate rebuilt and welded to body ($100)

Alternator in great condition

Newish clean headlights that are super bright (Cost me $300)

Newish diff in great condition

Mint tread on tyres (205/60/15)

Wheels suit it (15")

Some interior painted

New black front seat covers and new floor mats

Oh and I spent a good 4 hours cleaning most of the dirt/grease etc off the engine bay.

Drivers door lock damaged and removed thanks to theives

Starter motor slips but still starts vehicle after a few tries.

New spark plugs

Has WOF until November, Reg 2 weeks lapsed.

ALso have a bunch of spares

$1600! FIRM or SWAPs :-)

444471506a5717695456l.jpg

444471506a5717695469l.jpg

444471506a5717695490l.jpg

444471506a5717695500l.jpg

444471506a5636032005l.jpg

444471506a5717695512l.jpg

444471506a5717699858l.jpg

444471506a5717699877l.jpg

444471506a5717699887l.jpg

444471506a5717699900l.jpg

444471506a5717699909l.jpg

444471506a5717705098l.jpg

444471506a5717705110l.jpg

444471506a5717705124l.jpg

444471506a5717705139l.jpg

444471506a5717705158l.jpg

444471506a5717706588l.jpg

Edited by george.bryant
Link to comment
https://www.sau.com.au/forums/topic/189415-how-much-should-i-ask-for/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To plug the hole. The engine plant may not have known whether the car it was going into had a gauge or not. It was a long time ago and the integrations might not have been fully modern. Or they might not have cared because the extra inventory and processes to save a few cents on the sender might have cost more anyway. But please tell me you are not still confusing the idea of a pressure gauge sender, and an oil pressure light switch. The switch will be out there. In a separate hole. Probably with only one wire running to it. Running the light.
    • Blower needs to go low on the exhaust side, displacing the AC and PS, which you have to decide whether you want to keep and how and where to relocate if you do. Electric option for PS is, at least, helpful. Sadly, there is no workable 12V electric AC of any value. Whilst the blower is the last compression step before the throttle, and so it might seem a good idea to have it near the inlet manifold (as mentioned above), you probably want it to go through an intercooler first, so, having it on the opposite side of the car facilitates that air flow path. The turbo discharges into the blower, so proximity of the turbo's compressor outlet to the blower's inlet is nice. But then you might want to intercool that too, before boosting it again....which would probably be a ball ache. Routing pipes out to the front and back could be a bit shit. If there was room for (at least) a small (but preferably larger) water to air core on that side, then that would probably be the best approach. I guess a reasonable alternative would be to locate the blower where the alternator is (more or less, associated with the inlet manifold, per Matt's thought), and somehow incorporate a water to air core into the manifold, sort of like they do for modern blown V8s. The big difference here though is that those V8s have only the one throttle (upstream the blower) and only the one compression step (the blower) and no need for too much in the way of bypass/blowoff valves. Whereas in a twin charged 6, you do need to think about one or two bypass valves associated with the 2 compressors and you would prefer to have the intercooling done before the air has to pass through the throttle. You'd like the throttle to work approx the same no matter what the compression is doing. But if it is located in hot air stream before a cooler, then sometimes the air will be real hot, sometimes it will be quite cool, and the throttle mapping/response will be quite different between those two cases. The throttle, if sized for hot air, would be too large for cold conditions. It's all a ball ache.
    • Package SC on exhaust side. Remote mount turbo. Still a fair bit of room when you get creative on the inlet side of the motor too. Especially if you can get really creative with the welding, and effectively build it into the bottom of the inlet manifold. Would definitely take some design work, and some trial and error, to make sure flow works well still! Might be easier to just start with the Nissan March though... All the work is already done for you...
    • I'll sit down and get a post together 😁
    • The factory oil pressure sender is no longer in the car that's what is confusing me. In the Taarks adapter I have an aftermarket Bosch style pressure/temp sender and the factory temp sender only. Oil pressure is perfect. Where does the factory oil temp sender go to if there were never any gauges? Why was it there from the factory?
×
×
  • Create New...