Jump to content
SAU Community

Nismo Stagea Kits, Cheap!

AMS
 Share

Recommended Posts

AMS Grand Master

AMS

Posted
Posted

Let me start by saying, I miss you guys :nyaanyaa:

No other parts of any forum seem to have the close nit group such as this, anywho, on with business.

Got sent an email by Monkey Warehouse today. They have some Stagea kit that they would like to sell, so I'll be passing the cost price onto you guys. Prices are as follows:

NISMO Stagea - Front, Rear, Side Skirts: $749

NISMO Stagea - Front, Rear, Side Skirts, Spolier: $899

Pics: (RSFour's Stagea)

post-22914-1193191976_thumb.jpg

post-22914-1193192058_thumb.jpg

post-22914-1193192077_thumb.jpg

post-22914-1193192095_thumb.jpg

Also, I can sell you basically any Japanese part you want :P

Let me know if there is any interest in these kits!

Cheers,

Chris O'Connor

Advanced Motorsports

UPDATE: 4 kits to sell

post-22914-1193192013_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/190524-nismo-stagea-kits-cheap/
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...