Jump to content
SAU Community

Recommended Posts

All items in Canberra, can ship or arrange pickup. Call me anytime on 0410 378 429.

Enkei 17x9 Rims with tyres. Fantastic motorsport rims, 5x114. to fit GTR or similar. Two have a bit of gutter rash, though other than that they are in great condition. $1,000 including shipping anywhere in Australia using greyhound.

IMG_0312.jpg

IMG_0310.jpg

SR Rims with roadworth tires, $100

IMG_0295.jpg

SR Temp Sensors and attachments, $30

IMG_0307.jpg

Table/Rims. Rims are 16 inch Japanese rim, well made and can still be used. Alternatively you can take them with glass for as a side table. $200

IMG_0328.jpg

IMG_0327.jpg

Boost Guage $30, or free with any of the rims.

IMG_0300.jpg

Alpine Amp, 4 channel. Great Condition, $100

IMG_0297.jpg

BNR32 Centre Console Surround. No cracks or anything. $50

IMG_0304.jpg

Sub, 12 inch including box. $50

IMG_0308.jpg

SR20DET Head, engine had spun bearing head is fine. Have a box of bolts etc.. to go with it, though everything isn't in there. Has cams etc.. too. $100

IMG_0301.jpg

Edited by neergnevets
Hi Steve, I'll take the console surround. I'm in Canberra, southside. You have message.

Cheers

sorry bro i already purchased the cosole surround off him, am paying for it tomorrow afternoon, sorry mate,

cheers

, they are basically the same dimensions as the R33 GTR rims, will fill the guards of a 180sx no worries. Look fantastic, especially with the slightly stretched tyres fitted.

Edited by neergnevets

steven i just received the console now mait and that is not a genuin r32 gtr console. that has been sprayed before and also the top two clips are broken mait, i asked ya if all the clips were there and u said its in excellent condition so thats why i bought it, i had the same problem with my one mait and thats why i wanted one with th e two clips that clip in to the dash board on top of the triple tachos, so what are you going to do about this steve, i do not want the console because its clips are broken and its not sitting right, its sticking out like hard, so you have to do something about it mate because i needed a good one,

cheers buddy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...