Jump to content
SAU Community

Fmic?

W1ngnut

By W1ngnut,
in Australian Capital Territory

 Share

Recommended Posts

W1ngnut Proficient

W1ngnut

Posted
Posted

Hey ACT guys,

Hoping to buy and install an FMIC before the 11th for the skidpan day. Is the Type 1 JustJap kit reasonable bang for buck? I have the same intercooler (Bar and Plate 600x300x76 'Hybrid Copy') in the RS and has handled and cooled 18psi no worries.

Any info / ideas / suggestions would be much appreciated.

Cheers

Sam

Link to comment
https://www.sau.com.au/forums/topic/191256-fmic/
Share on other sites
Baconer Grand Master

Baconer

Posted
Posted

From what ive read those Just Jap ones require a lot of trimming and cutting (fan blades, under washer bottle, front reo bar and front bar)

Was looking at the ARC and Blitz LM FMICs which plug into stock pipes and pretty much fit right on without any trimming (except for reo) but they cost around $1000

Link to comment
https://www.sau.com.au/forums/topic/191256-fmic/#findComment-3441564
Share on other sites
W1ngnut Proficient

W1ngnut

Posted
  • Author
Posted

I've noticed this as well Baconer. Was looking closely at the ARC kits, I just can't justify the extra cost for them as much. The Just Jap ones from what I read on the JJ posts is that it's all to do with the prep work so you don't have to trim the fan blades. Under washer bottle is easy sorted to fill the hole. As for the other trimming/cutting, i would expect that the Blitz LM and ARC kits require just as much cutting of the reo bar and front bar...

Thanks for the help though guys, its good to hear other peoples thoughts.

Link to comment
https://www.sau.com.au/forums/topic/191256-fmic/#findComment-3441670
Share on other sites
Sauce Experienced

Sauce

Posted
Posted

I've got the JJ kit in my 33. It's getting the job done, though I'm still running standard boost because I dont have time to get the boost gauge and controller put in to up it a but. Laziness ftw! Had to hack the front bar and reo to bits but I think that's pretty much a given for a FMIC regardless of what brand it is.

Link to comment
https://www.sau.com.au/forums/topic/191256-fmic/#findComment-3441772
Share on other sites
W1ngnut Proficient

W1ngnut

Posted
  • Author
Posted

Cheers for the info Sauce. I'm still runnin stock boost as well as the fuel pump is still standard... I'll be taking out my eboost2 from the subie later to install into it if I get bored.

The main thing I was really worried about was fitting the cooler piping across the radiator and having to cut the fan blades.

Link to comment
https://www.sau.com.au/forums/topic/191256-fmic/#findComment-3441930
Share on other sites
R33_ACT Community Regular

R33_ACT

Posted
Posted

cutting the fan blades is no big deal its a must as i fitted a similar fmic to my 33 the top pipe touches the bonnet so its as highest it will go and i still had to trim the fan as for the water bottle didn't have to touch that...its a pretty big job cutting and shaving the reo and front bar but worth it

Link to comment
https://www.sau.com.au/forums/topic/191256-fmic/#findComment-3444317
Share on other sites
R33_ACT Community Regular

R33_ACT

Posted
Posted
There's no major side effects to trimming the fan? It's spins awfully fast and can unbalance easily no?

naa not giving me any problems at all....i will pull it off one day and tidy it up as i just cut the blades with side cutters without taking it off the car

Link to comment
https://www.sau.com.au/forums/topic/191256-fmic/#findComment-3444360
Share on other sites
R33_ACT Community Regular

R33_ACT

Posted
Posted
ahh right... well if i end up trimming the blades i might sand paper them down slowly and shape them so it looks normal

i was thinkink when i take it off i'll make some sort of template so i can get them all exactly the same length

Link to comment
https://www.sau.com.au/forums/topic/191256-fmic/#findComment-3444379
Share on other sites
JD-33 Community Regular

JD-33

Posted
Posted

I would say if you had more time to go to Platinum Performance in Sydney, they did my Hybrid Tube n Fin plus installation for $700.. what a bargain! :blink: .. then again it was at the end of the financial year, dont know if they would chrge different now, but they were awesome! even drove me like 15kms to the shops and picked me up when my car was ready :P

Link to comment
https://www.sau.com.au/forums/topic/191256-fmic/#findComment-3444483
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By GTSBoy · Posted

      Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Bireley_32
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Bireley_32 · Posted

      Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • MBS206
      Starting again

      By MBS206 · Posted

      The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
×
×
  • Create New...