Jump to content
SAU Community

Recommended Posts

nah man, getting the car to the pit somewhere next week, not sure if the 18" now will pass the pit, if they dont, i'll end up paying another $50.60 for the inspection fees.

And i am actually thinking about changing the rims. The one i have now is volks racing 18" tri spokes. 265/35 new tyres.

Would be happy to trade the existing rims with the standard ones and perhaps they could compensate me a little for that.

Link to comment
https://www.sau.com.au/forums/topic/19159-gtr-standard-rims/#findComment-403730
Share on other sites

Sub , check the tyre placard which should be on the driver or passenger door pillar inside when you open the door.

Little white sticker thingy. Check to see if it is complied with 18's as well as 17's.

If it is and you have new or near new Aust spec tyres ( ie. DOT approved) and they are not poking out past the guards then there should be no grief.

I would suggest to go to the Welshpool licensing centre .......

Cheers

Ken

Link to comment
https://www.sau.com.au/forums/topic/19159-gtr-standard-rims/#findComment-405884
Share on other sites

Originally posted by sub

welshpool licensing is better than the others? I normally go to the fremantle ones because it is nearer. Anyway, if the welshpool ones is better, welshpool it is.

Never been to Freo but I can tell do NOT go to warwick and East Perth is fairly hard.

Cheers

Ken

Link to comment
https://www.sau.com.au/forums/topic/19159-gtr-standard-rims/#findComment-406291
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...