Jump to content
SAU Community

Recommended Posts

Alpine stereo components for sale

Reason for sale is traded 4wd in for a dirt bike

type R 6 " splits for sale approx 1.5 years old. 1 tweeter has a little grazing on it otherwise in good condition and work well

$175 ONO see photo

Type S 6 " speakers also in good condition and work well. bout 1.5 years old

$80 ONO see photo

V power MRP-F450 4 channel amp. bout 3 months old and in perfect condition. 700w max.

$300 ONO see photo

OR $ 520 for all the stereo gear

ALL OFFERS CONSIDERED EVERYTHING MUST GO

Please phone or sms Eddie on 0407 750 566 as i only get on the comp every few days

OTHER GEAR

MOMO genuine steering wheel near new condition beautifully made in italy. the wheel is pilota cut which means it is shaped to fit your hands and fingers in about 3 different positions. Great condition wheel does NOT include screws as they should be supplied with your boss kit which can be purchased at autobarn/super cheap/repco etc

$250 ONO see photo

set of 4 rubber dish 4wd floor mats. 1 month old

$30 ONO see photo

Light force SPOT LIGHTS biggest and brightest on the market near new great condition

close to $1000 new, sell for $500 ONO see photo

Maxi Track 4wd high lift jack, used once only to lift boat trailer great condition

$85 ONO see photo

Maxi Track tree saver winch strap brand new never used

$45 ONO see photo

also have a TJM 10 000 Lb winch for sale with wire rope and remote control works well

but not sure on price as yet but let me know if theres interest

OR $620 for all 4wd gear

ALL OFFERS CONSIDERED EVERYTHING MUST GO

Please phone or sms Eddie on 0407 750 566 as i only get on the comp every few days

post-28910-1193821039_thumb.jpg

post-28910-1193821112_thumb.jpg

post-28910-1193821202_thumb.jpg

post-28910-1193821351_thumb.jpg

post-28910-1193821537_thumb.jpg

post-28910-1193821643_thumb.jpg

post-28910-1193821759_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/191620-gear-for-sale/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...