Jump to content
SAU Community

Recommended Posts

hi guys, im from the states and i need of a bit of help with my r33. ive checked the turbo, its good in working order, i just changed plugs and checked gaps for each. the car runs super rich about 9-10 a/f at low throttle just cruising, however at WOT the car leans out as it builds boost and jerks violently. also if i hold the throttle about half way it will build about 3 or 4 pounds and feels as if im brake boosting, suction from the intake/turbo is loud but no acceleration without the jerking. but as soon as i punch it it knocks and flips out. i changed plugs again and no help also checked vacuum sources and double tripple checked everything. im at a loss. there are no check engine lights. 127km on the car and motor. also car reacts the same way with the boost controller on or off.

mods include:

pod filter

front mount

turbo back exhaust

greddy profec boost controller at .6 bar

afc neo with decel at 1% throttle, 1.2 at 1000 and 3.8 at 2000. no tune.

thank you all for your help.

Edited by Jbunn2001
Link to comment
https://www.sau.com.au/forums/topic/192259-rb25det-acting-strange-help/
Share on other sites

ive only experianced this once. and im sure you've probably checked i i found i tiny hole in the intake pipe just after the cooler... was fine cruising... hit the throttle and yeah feels like break boost then WACK and big jerk of the car.

replaced the silicone hose no problem from there on.

ill try that again, maybe i over looked something. also for an update i just drove the car after i did nothing...... lol and it hiccupped a few times and was maintaining boost, but i ran ass rich this time all the way through only hit 12.2 after the hiccup then back down to 9.9- 10.3. so im thinking of a few things i need to address.

Coils.... ive already ghetto taped mine hoping they wouldnt arch

AFM- but i would assume i would have a check engine light

or... i stilll dunno.

i will check the intercooler piping and change the silicone cupplers and get some propper t-bolts.

thanks again

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...