Jump to content
SAU Community

Recommended Posts

Guest Dakidmas

Hey guys,

I will be purchasing my first ever skyline but don't have a clue on what to look for in way of problem areas with these cars

(r33 gts-t), i am moving up from owning a silvia so i really don't know much in way of the engines on these things.

Any advice would be greatly appreciated, engine, body, interior ect. it all helps.

Thanks, Clint.

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/
Share on other sites

Hey dude,

well problems i've had with my car are the book leaking on rainy days your boot can get pretty wet.. but some silicon fixed that, oh and if the car has standard shocks then its pretty common for the rear shocks to be rooted as well.. other than that the car has been pretty solid so far with no major problems, but then again i bought my car pretty much stock from japan i dont think my car had been thrashed everything is in top condition except for the shocks which just went after i was driving it though

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/#findComment-406328
Share on other sites

I got this from a site, hope it helps you out a bit!!

(Sorry bout the large post though)

We are fairly lucky that we have a wide range of Skylines available thanks to our second-hand car importing industry which has been going strong for over a decade. With so many cars on the market, there is no reason to buy a lemon.

Here are some points to watch for with Skylines.

· The year of manufacture can be found by looking at the front seatbelts, near the floor mounting point. There is a fabric tag with the seatbelt specifications and the year of manufacture sewn onto the webbing.

· Inspect the welded seams in the front door sills just below the plastic kick plate. This is where I have seen rust start to form on Skylines, especially the R32. The R33 has an identical seam, so these will also show in years to come.

· Remove the rubber around the boot rim - this is a prime rust spot in any car. While you are in there, look in the side panels and make sure they are not full of water.

· Feel inside the panels in the boot where the jack is - debris found here will tell a story.

· Watch for glass (broken rear window or tail lights at some point)

· Inside the engine bay, look for crayon or chalk marks on components - this may indicate they have been replaced with second-hand parts.

· Crawl under the car and inspect behind the front and rear bumpers for signs of collusion damage.

· If you are keen, use a set of vernier callipers to measure the panel gaps especially on the doors.

· Mechanical - a noisy ceramic turbo isn't a good sign - see if it has been replaced with a conventional steel type.

· With the front wheels off the ground, check the play in the top end - any more than 5mm and there could be expensive repairs needed.

· Watch the oil pressure when the car is hot - Keep in mind the oil pressure sender is prone to failure.

After Purchase

· As you may not know the history of the car, it is best to start with a full service.

· Air filter - replace.

· Fuel filter - replace.

· Run a bottle of injector cleaner through the system with the next tank of petrol.

· Oil filter - replace, and change the oil. If there is a sludge problem do a hot oil change and repeat within 1,000 km. Don't use an engine flush treatment.

· Automatic transmission - have the oil changed. The transmission cooler should also be flushed.

· Spark plugs - replace. Make sure they are replaced with the platinum resister type.

· Timing belt - inspect and replace. Nissan specify a 100,000 km life for these. Be safe and prevent the rain of valves.

· Radiator - add plenty of anti-freeze. Without the protection of anti-freeze (corrosion inhibitor) there are parts that will corrode and eventually cause you grief. Check the condition of all the hoses while you are at it.

· Battery - monitor and replace if needed. Japanese car batteries are smaller than the regular sized car battery, and it may be the factory fitted battery (over five or six years old)

· ECU - reset it. Make it learn our driving conditions.

· Drive safe, respect the roads and enjoy the ride...

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/#findComment-406342
Share on other sites

I got mine checked with the RAA, they did a 4 hr inspection on it.

They checked almost everything on it and gave a recommendation on if to buy or not.

It helped me out cause they saw stuff i didnt, and it cost $165.

Bargain if u ask me, saves the nightmares of gettin a lemon

HAPPY HUNTIN!

Link to comment
https://www.sau.com.au/forums/topic/19358-advice-on-r33s/#findComment-406344
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...