Jump to content
SAU Community

Stolen R33, Sau I Need Your Help!

R33LIN

By R33LIN,
in South Australia

 Share

Recommended Posts

Madaz Grand Master

Madaz

Posted
Posted

yeah i looked and swore it was the one @ broadview

was it an inside job?? one of your mates or a mate of a close mate

well done on getting that footage Howie...

lets hope they don't pull your skyline out with a forklift :w00t:

R33LIN Collaborator

R33LIN

Posted
  • Author
Posted (edited)

as mentioned above, car has been found in one piece..

Again, i would like to take this opportunity to thank everyone for your support. the support has been enormous and i could not have done this without it.

thanks guys,

:w00t:

(Mods is it possible to close/delete this thread?)

Edited by R33LIN
Howie Grand Master

Howie

Posted
Posted

Good to hear bro... if you need a hand fixing anything they fk up, let me know. I'm no mechanic but not afraid to get my hands dirty.

So next cruise destination broadview guys ? :w00t:

ted180 Mentor

ted180

Posted
Posted
Whats the deal with this broadview car yard?

Is this where all the stolens end up?

its unknown if all the skylines that have been stolen recently are the ones found there, not like the police are going to say anything yet,

but put 2 and 2 together and its pretty obvious.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...