Jump to content
SAU Community

Recommended Posts

Make: Holden

Model: VX S Series II

Milage: 82,000

Transmission: Auto

Colour: White

Location: Geelong, VIC

Complied? YES

RWC supplied? YES

Currently registered? YES till August 08

Price: 13,000 or 12500 without RWC

Contact: 0401910780 or EMAIL: [email protected]

Comments / Modifications: 2.5" Catback Exhaust , Pacemaker Extractors , Lowerd on SSSL king springs and SSL Lovells, Stage 2 Shift kit, Yella Terra 1.97 High Ratio Roller Rockers || Great Condition, only minor scrape marks under front bar, Small dent the size of a 5 cent piece in passenger door and minor scratch on rear quater panel no longer then an inch. Interior is immaculate. Rims in pictures not offerd with the car. The car will be sold on 15" Interceptors. All reasonable offers will be considerd including trades.

Images:

post-44600-1196594350_thumb.jpg

post-44600-1196594396_thumb.jpg

post-44600-1196594420_thumb.jpg

post-44600-1196594446_thumb.jpg

Edited by jaysevu
Link to comment
https://www.sau.com.au/forums/topic/196049-holden-commodore-solddddddd/
Share on other sites

Its a pity your not in NSW,

Thats the sort of car im after. I have a 96 Series 2 R33, 3" cat back (5Zigen?) exhaust, HKS pod. I imported it back in 03 through www.directimported.com.au

Its just hard to get the baby out of the back seat these days... So I have to sell my beast.

Cheers

Matt

Very frustrating isnt it Matt .. Just looking at potential cars to check out once the commo is sold, alot of nice ones interstate! .. gota weigh up whether or not its worth the travel i suppose!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
×
×
  • Create New...