Jump to content
SAU Community

R32 With Neo25

samedy-sam
 Share

Recommended Posts

samedy-sam Explorer

samedy-sam

Posted
Posted

Make: nissan skyline

Model:1989 R32

Milage:154xxx new engine was put in at 130xxx

Transmission:manual

Colour:blue

Location:brisbane QLD

Complied? yes

RWC supplied? yes

Currently registered?yes

Price:14000 ono but would like trades for a 05+ hatchback for the girlfriends mainly a swift

Contact:call/txt anytime on 0420751972 or email me at [email protected]

Comments / Modifications: it has a Neo 25 engine in it, trust front mount, 3' exsharts, R33 diff, 4' heavy duty drive shaft, apexi ACF neo, koni coilovers in the rear and jic springs and shocks upfront, has GTR brakes up front with braded lines, turbosmart BOV, 3 gauges, has run a 13.9 at 105mph on 8 psi has never been passed 8 psi, has 18s 5 star rims. thats all i can think of at the moment

Images:post-42158-1197156918_thumb.jpgpost-42158-1197156941_thumb.jpg[attac

ment=133383:IMGP0015.JPG]post-42158-1197156983_thumb.jpgpost-42158-1197157006_thumb.jpg

post-42158-1197156963_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/196798-r32-with-neo25/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...