Jump to content
SAU Community

Fs: Adj Cam Gear, Oil Catch Can, Stock Rb25det Neo Injectors

QWK32
 Share

Recommended Posts

QWK32 Veteran

QWK32

Posted
Posted (edited)

Item: Stock R34 GTT (RB25DET NEO) Injectors (6 of them)

Age: Unsure, come off an engine not in a skyline

Condition: Good, they had no leaks and they all appear to be good (no broken bits or cracks)

Price: $200 $150 ono pick-up, postage extra

To Fit: I think they just fit top feed high impedance NEO engines

Location: Brisbane Southside

Contact: Reply here or PM me.

Comments: I put new sard injectors in a friends car for him and he gave me the old ones for doing the work for him. they also come with the clip things that hold them in.

Item: OS Giken adjustable cam gear

Age: 6 months.

Condition: Excellent, was only on the engine for 6 months

Price: $100, $10 extra posted

To Fit: All RB twin cam engines. if you have VVT it wont go on the inlet side without modification

Location: Brisbane Southside

Contact: Reply here or PM me.

Item: D1 Spec oil catch can Blue.

Age: 6 months

Condition: Excellent

Price: $50, $10 extra posted

Location: Brisbane Southside

Contact: Reply here or PM me.

Comments: comes with the fittings on the catch can but no lines and no baffles inside.

Edited by QWK32
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...