Jump to content
SAU Community

Vortech's owner in troub, need urgent help: Where can you get an emission test in SA?


Recommended Posts

A friend of mine is getting a Vortech SC kit for his car. He checked with registration who then referred him to Regency. :P

Regency requested a emission test result to be able to register the car!!!!! He has been quoted $4000 for the test in SA ;)

The kit on this car is exempted from emission control everywhere in the world. The kit has a placard attached to the supercharger stating so. The car is only 3 years old and set the world record for the lowest emission engine/exhaust system. Regency still would not register this car unless it has the test done in Australia.

What the hell is going on with the government? What is the fairness here? Does every car need a emission test if something is done to the car? Does LPG car need a emission test when LPG get installed?

Do you guys know of any other ways around this problem?

Could you guys tell me where Regency is and who work there?

What car is it for?? I would suggest calling them, as most of the common kits have been EPA tested... Also speak with Tonkin and associates in Adelaide.. They are consulting engineers that i think do the testing for CAPA.. All you need to do, it the emmssions has been done on the kit by CAPA is to pass a noise test.. Not much at all $$$$...

Originally posted by SR910

A full drive cycle emissions test at mitsubishi motors is just upwards for $4,000.

Yes, this is what my friend told me too.

Is there any other place that carry out the test as well? Doe Holden in Elizabeth do this test?

I would just ring CAPA, as i had to go through this with my Powerdyne kit when i lived W.A. All you have to do is a noise test.. As the kit for the 5.0L is already Emmissions compliant..

What Vortech do you have Is it the V2 (silent Vortech) as the normal V-1 S Trim may not pass..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...