Jump to content
SAU Community

Recommended Posts

Hey

see thread here for background information http://www.skylinesaustralia.com/forums/S1...Fc-t196648.html

Got a R34 GTT Power FC to plug into my series 1 automatic Rb25det Stagea (same ecu plug)

Is this actually R34 GTT Pfc?

PFCER34 010-0155 ECU

FCC2 NT 020-00584 HAND CONTROLLER

just want to check.

Im hoping it will wire up ok with Andys 51pin volt trick, I think the attessa should be ok

anyone experienced with wiring a Power FC with 4wd (with automatic, I doubt THAT?) ;)

Ive found a few differences between the R34 Skyline ECU pinouts and the stagea ecu pinout, nothing too "out there" by the looks

Im confident the couple of differences Ive found can be handled and rewired, if infact necessary.

I'll have help to install and test, but will leave it in the hands of an experienced electric circuit handyman to make it all work, then tune

auto electrician perhaps? or a south aussie sauer?

Also, please, is the R34 GTT Power FC pinouts exactly the same as the Skyline stock R34 GTT ecu pinouts?

Link to comment
https://www.sau.com.au/forums/topic/197537-power-fc-confirmation/
Share on other sites

I always thought the PFC was only made for manual skylines/stageas. And plugging it into an auto isn't going to be successful unless you do some wiring modifications.

I think SK had a PFC running on his stagea but he did have to modify something to make it work. It's not a plug and play affair.

Also wouldn't a R33 PFC be more suited to your car? I thought the S1 Stagea's didn't run a NEO RB25det....

Edited by KeyMaker
I always thought the PFC was only made for manual skylines/stageas. And plugging it into an auto isn't going to be successful unless you do some wiring modifications.

I think SK had a PFC running on his stagea but he did have to modify something to make it work. It's not a plug and play affair.

Also wouldn't a R33 PFC be more suited to your car? I thought the S1 Stagea's didn't run a NEO RB25det....

there are Stagea's - both manual and converted manuals from autos, both series 1 and series 2, that run the PowerFC with very minor alteration

the stagea ecu plug is same as r34 NOT r33

stagea series 1 dont run the neo, but stagea series 1 and series 2 ecu is the same (plug for pinouts)

I have the Stagea stock ecu pinout diagram and the R34 Skyline stock ecu pinout diagram, wiring mods will be done

I expect that I may lose VVT, thats ok, can tune around it to a certain extent

I expect that eventually the auto will fail and require a rebuild. It is a fact that plenty of R33 Rb25dets AUTO run the powerfc successfully

I could do a alteration to the auto at MV Autos with a manual shift setup for the auto box.

Anyone care t0 confirm the following?

Is this actually R34 GTT Pfc?

PFCER34 010-0155 ECU

FCC2 NT 020-00584 HAND CONTROLLER

Also, please, is the R34 GTT Power FC pinouts exactly the same as the Skyline stock R34 GTT ecu pinouts?

cheers

you, SIR, are a legend

thank you

Now Im confident I have all the right info to get this to work

Ive identified the differences between the 2 pinouts, so a simple rewire cut n shut job can be done

I reckon a qualified auto electrician, with full insurance in case they fry the pfc, will be able to do the wireup for me

I dont know electronics and am not comfortable doing the wiring myself

That includes Andy's "secret squirrel trick" using a 10.3V zeneer diode between Pin51 and Ignition and a 400ohm resisitor between Pin51 and Earth

at this stage I wont be going to a mechanical auto shift setup for the gearbox, maybe later, maybe later

yeah the stagea's run the R34 plug

series 1 and 2

I guess my post was a silly question; my bad.

Went to Boostwerx today and they reckon, with the info I have, that they'll have it wired and tuned.. theres a guru auto sparkie floating around they know so they are confident of a positive outcome.

:ermm:

just gotta wait till end of Feb.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...